Go Back   Honda-Tech > Honda and Acura Model-Specific Technical Forums > Ridgeline : MDX : Odyssey : Pilot : RDX
Sign in using an external account
Register Forgot Password?
Search


Reply
 
 
 
 
LinkBack Thread Tools Search this Thread
Old 02-22-2011, 06:53 AM   #1
Honda-Tech Member
 
Join Date: Feb 2011
Posts: 7
iTrader Rating: (0)
Default 2006 Pilot drive belt tensioner problem

I started working on replacing the timing belt and water pump on my 2006 Pilot (first time for both me and the vehicle), and got stopped in my tracks before I got very far. For the life of me, I cannot get the serpentine/drive belt tensioner pulley to release or move, or whatever the term is for getting it to relax enough to remove the belt. I suppose it's important to note that the only manual that I have available to me for this job is the Haynes Pilot 2003-2007/MDX 2001-2007, and I believe that the tensioner that's described and illustrated in the manual is different than mine. I have dealt with several different tensioners in my life, and I don't remenber one that remained "frozen" or locked, or in other words not budging even a millimeter, even after me being assisted by a 24" breaker bar. Also, this is the first one I've seen that has a sort of hydraulic appearing cylinder that seems (by noting its position relative to the pulleys) to be functioning in a way similar to the tensioner adjuster for the timing belt.

Can anyone tell me if (contrary to all the written instructions I've read) this type of adjuster requires a different or special tool (other than the sockets and extended handled ratchet) or procedure. I spent 2 or 3 hours last night trying to figure this out. I've been trying to avoid an excess of brute force, after having read a post by someone who reportd damaging a pulley by trying to pry a tensioner open, although I don't recall it being described as the same type.

Sorry this is so wordy, but I really need some help, and I am trying to be as specific as possible.

Thanks to anyone who may try to give me a hand.

p.s. - - Something I just remembered; the upper tensioner pulley that the manual (Haynes) refers to as the one to turn to release the tensioner does not have a nut locking it, but a Torx fastener of some sort that is too shallow to get much grip. I vaguely recall someone else posting about this type of tensioner requiring a Honda tool of some sort. Is this tensioner unique to the 2006 model? If not, why aren't there more comments (or complaints) about it? Or, am I just missing something that should be obvious? Uh-oh, I think my sleep deficiency is starting to show.

Last edited by vltjr; 04-30-2011 at 02:51 PM.
vltjr is offline   Reply With Quote
Old 02-22-2011, 08:44 AM   #2
Honda-Tech Member
 
Join Date: Feb 2011
Posts: 7
iTrader Rating: (0)
Default Re: 2006 Pilot drive belt tensioner problem

Well, I have to give up on the project for today. The Pilot is required to perform taxi service this afternoon (good thing I'm not going to be doing the driving), so I have to put everything back together. I guess I need to be somewhat better prepared when I take the next shot at it. I'd like to get a copy of the real service manual, but it's just not in the budget right now, especially after purchasing the timing belt/water pump parts. I suppose I can take some advice I read on this forum, and see if one of the local dealers will let me copy what I need.

Thanks to everyone who read of my frustrating experience. I'm going to have to do this soon, so I'm still looking for everybody's ideas and advice.

Thanks.
vltjr is offline   Reply With Quote
Old 03-02-2011, 02:30 AM   #3
Honda-Tech Member
 
civicsir924's Avatar
 
Join Date: Nov 2004
Location: Portland, OR
Posts: 57
iTrader Rating: (0)
Send a message via AIM to civicsir924
Default Re: 2006 Pilot drive belt tensioner problem

Sounds like you have the J35Z1 engine. Just make sure you are on the 19MM that is casted on the actual tensioner and not the e-torx or the lower tensioner pulley bolt. Yes it is pretty tight due to hydraulic type tensioner. However get on that 19mm and slowly push on it counter clockwise, keeping steady force and it should enough to get the belt off. Just dont try to push it as far as it will go cause I have seen people break them. If you still cant get it after that just take some shears ect and cut the drive belt off and go from there.
civicsir924 is offline   Reply With Quote
Old 04-30-2011, 02:50 PM   #4
Honda-Tech Member
 
Join Date: Feb 2011
Posts: 7
iTrader Rating: (0)
Default Re: 2006 Pilot drive belt tensioner problem

civicsir924 - Thanks for your advice. Sorry I didn't respond to your post until now, but I totally put the TB job on hold until this weekend (coming up on 103,000). By following your instuctions re the hydraulic tensioner - slow but steady force - I was able to finally get the thing to work. Once I got it loose, it's been working easily and smoothly. Thanks again.

Of course, now that I've undertaken this project again, I've run into new obstacles.I've already posted a plea for help here:

Honda Pilot (03) Timing Belt & Water Pump

I would feel a little too whiney if I directly repeated it again here.
vltjr is offline   Reply With Quote
Old 05-05-2011, 09:39 AM   #5
Honda-Tech Member
 
GreenD's Avatar
 
Join Date: Mar 2002
Location: pasadena, ca
Posts: 804
iTrader Rating: (0)
Default Re: 2006 Pilot drive belt tensioner problem

Sorry if this is a little late. This is for an 04 but it should be almost the same:

http://www.piloteers.org/forums/18-m...placement.html
__________________

Quote:
Originally Posted by Cuda70

I think the thing that really scares me the most is the simple fact that my future will someday be in the hands of some of you idiotic tools here in Honda Tech.
GreenD is offline   Reply With Quote
 
 
 
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
tensioner/pulley Bill Johann Ridgeline : MDX : Odyssey : Pilot : RDX 0 11-23-2014 07:10 PM
How-To: Replace Timing Belt, Timing Balancer Belt and Water Pump on a F22B1 TouringAccord Honda Accord (1990 - 2002) 647 10-11-2014 04:27 PM
D16Z6 Tensioner! Need help removing/replacing. poordna Honda Civic/Del Sol (1992 - 2000) 11 05-26-2012 01:47 PM
h22 manual tensioner adjustment.. HOW? the boogler Honda Prelude 10 03-25-2012 07:18 AM
Correct Method for Timing Belt Tension yosuthnmasa Honda Civic/Del Sol (1992 - 2000) 8 04-08-2008 08:29 AM


Tags
2003, 2006, adjuster, belt, drive, honda, honds, locate, oddyssey, pilot, pilottensioner, special, tensioner, timing, tool

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



Join Honda-Tech.com

All times are GMT -8. The time now is 07:03 PM.



2014 Copyright, InternetBrands Inc.
Powered by vBulletin® Version 3.8.7 AC1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.

Honda and the Honda marquee are registered trademarks of the American Honda Motor Company, Inc. Neither American Honda Motor Company nor its subsidiaries or affiliates shall bear any responsibility for Honda-Tech.com content, comments, or advertising. Honda-Tech.com is not affiliated with American Honda Motor Company in any way. American Honda Motor Company does not sponsor, support, or endorse Honda-Tech.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.
Emails & Contact Details