*Official H/T OFFROAD/LIFTED CR-V thread!*
#1702
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
If anyone has a set of ap1junky front spacers or any 1" front spacers pm me.
I plan on lifting a civic wagon. 1" spacers on front and flipping rear lca for 1" in rear. Should even it out.
I plan on lifting a civic wagon. 1" spacers on front and flipping rear lca for 1" in rear. Should even it out.
#1706
#1708
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
I was thinking about putting some 1" pucks on it... After the springs settled, all the parts i trimmed down it wasn't enough. If you know of any place right off hand that sells some cheap that would be great. If not I'll have to get some made.
#1709
Honda-Tech Member
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
spacers? i can make some ill see if i have the 1 inch aluminum.... i should start selling them
im thinking about going springs myself with spacers...the coilovers are fricking hard....
im thinking about going springs myself with spacers...the coilovers are fricking hard....
#1710
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
Kinda spacers... They have to be able to be bolted on the top of the strut and to the strut tower obviously. And yes, i hate coilovers with a passion. My V was slammed around 5 years and i went through 4 different sets of struts, then again the setups i had weren't vehicle specific bc nobody offered one at the time so the spring rates were way different then they were supposed to be but with every car I've ever had it seems my shittier cars rode much better with just springs lift or lowering. Much less to worry about as well
#1711
Honda-Tech Member
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
if anyone needs spacers made out of aluminum let me know... i have 1/2 inch think spacers...you can stack them if you want....to meet the height that you want....
im guessing, youll need to replace the stock stud/bolts with a longer one....if you want 1 piece thick spacers let me know...PM me for any questions
im guessing, youll need to replace the stock stud/bolts with a longer one....if you want 1 piece thick spacers let me know...PM me for any questions
#1713
Honda-Tech Member
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
is it something similar to this:
lmk..
#1714
Honda-Tech Member
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
biting the bullet and going back to stock height. have too many things tying up my extra cash to have to worry about breaking something because of the lift.
#1716
Honda-Tech Member
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
ball joints, control arms mainly. i already had to replace an upper control arm because the ball joint was screwed up. tired of the low mileage also.
#1717
Honda-Tech Member
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
QWRTY yeah like that but i can, make a 1 piece thick spacers...
NONAME....damn i might just stay where im at....hearing all these problems youre having, forget it... not only that im 2wd...lol
oh yeah i can make wheel spacers too...im using a set my self
NONAME....damn i might just stay where im at....hearing all these problems youre having, forget it... not only that im 2wd...lol
oh yeah i can make wheel spacers too...im using a set my self
Last edited by ARMED; 07-11-2015 at 10:03 PM.
#1718
#1720
#1721
Honda-Tech Member
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
Sorry guys not on here much look me up on FB if you need to contact me.
JUAN CAMBERJNKY MARTINEZ
JUAN CAMBERJNKY MARTINEZ
Last edited by ap1jnky; 01-15-2016 at 02:26 PM.
#1722
#1723
Honda-Tech Member
Join Date: Oct 2005
Location: monument, Co., USA
Posts: 940
Likes: 0
Received 0 Likes
on
0 Posts
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
I made 3/4" HDPE spacers for the rear to fix the sag and im having trouble finding extended tophat studs. any pointers?
I dont really want to use bolts and need to have them tack welded into place. what are you guys doing for extended studs? i looked @ home depot, pep boys, local hardware store, just searched online...
I dont really want to use bolts and need to have them tack welded into place. what are you guys doing for extended studs? i looked @ home depot, pep boys, local hardware store, just searched online...
#1724
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
I made 3/4" HDPE spacers for the rear to fix the sag and im having trouble finding extended tophat studs. any pointers?
I dont really want to use bolts and need to have them tack welded into place. what are you guys doing for extended studs? i looked @ home depot, pep boys, local hardware store, just searched online...
I dont really want to use bolts and need to have them tack welded into place. what are you guys doing for extended studs? i looked @ home depot, pep boys, local hardware store, just searched online...
#1725
Honda-Tech Member
Join Date: Oct 2005
Location: monument, Co., USA
Posts: 940
Likes: 0
Received 0 Likes
on
0 Posts
Re: *Official H/T OFFROAD/LIFTED CR-V thread!*
They are not a common stud. Using bolts and matching hardware is your best route. If you dont have a welder or a friend with one, the cost to have it done would be minimal(if you prep the top hat by grinding/ sanding off the paint.). I used 1/2" spacers and had enough thread to use stock studs