Ignition timing on a rebuilt 1991 Civic DX - Honda-Tech
Go Back   Honda-Tech > Honda and Acura Model-Specific Technical Forums > Honda CRX / EF Civic (1988 - 1991)
Log In 

Ignition timing on a rebuilt 1991 Civic DX

LinkBack Thread Tools Search this Thread
Old 06-01-2009, 10:42 AM   #1
Honda-Tech Member
DennisWaller's Avatar
Join Date: Jan 2004
Location: Bellingham, WA, USA
Posts: 47
iTrader Rating: (0)
Default Ignition timing on a rebuilt 1991 Civic DX

After completely rebuilding this D15B2 engine including replacing the timing belt I found it impossible to advance the timing by turning the distributor to reach the recommended timing setting of 18 degrees BTDC. There are three grooves in the crankshaft pulley and the shop manual recommends setting the timing at the middle groove.The maximum advance I can achieve is the first of the three grooves in the crankshaft pulley.

I suspect I have installed the camshaft one tooth too late in relation to the the timing belt but I would appreciate the advice of other mechanics before redoing that job.

This is an interference engine. However it runs well and is quiet so I don't think any of the valves have been damaged by hitting the top of the pistons. I have not driven the car since I discovered the problem with the ignition timing.

Dennis Waller
Foreign Auto Service.
DennisWaller is offline   Reply With Quote
Old 06-01-2009, 11:21 AM   #2
Honda-Tech Member
DCRB's Avatar
Join Date: Jan 2008
Location: Portland, OR, USA
Posts: 5,155
iTrader Rating: (0)
Send a message via AIM to DCRB
Default Re: Ignition timing on a rebuilt 1991 Civic DX

from what i know one tooth off isn't enough to cause interference, but will make it run like poop. i'd double check the timing if i were you.
Build Thread - My 88 ED6 Daily - 97 Vr6 Passat Wagon
Originally Posted by BETOSCOUPE View Post
Plus my boss gets mad at me because she can't hear me 1/2 the time while I am on the phone with her lol "WHAT IS ALL THAT NOISE" - Bitch..... Its my Type R foo lol
DCRB is offline   Reply With Quote

Similar Threads
Thread Thread Starter Forum Replies Last Post
Crankshaft pulley bolt zsiya Honda Accord (1990 - 2002) 9 12-23-2013 09:51 PM
Left drive shaft will not seat into the trans DennisWaller Honda CRX / EF Civic (1988 - 1991) 1 01-24-2009 01:06 PM
Cylinder bore surface finish DennisWaller All Motor / Naturally Aspirated 4 08-12-2008 09:02 AM
Is there any difference between GMB and NPW water pumps DennisWaller Acura TL, RL & ZDX 1 03-30-2005 09:57 AM
Air conditioning in 1991 Honda Civic DX DennisWaller Honda CRX / EF Civic (1988 - 1991) 0 01-19-2005 02:17 PM

1991, 88, advance, camshaft, civic, county, dx, ef, honda, ignition, indiana, koscuikosico, police, rebuilt, scanner, set, setting, timing

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

All times are GMT -8. The time now is 06:21 PM.

Honda and the Honda marquee are registered trademarks of the American Honda Motor Company, Inc. Neither American Honda Motor Company nor its subsidiaries or affiliates shall bear any responsibility for Honda-Tech.com content, comments, or advertising. Honda-Tech.com is not affiliated with American Honda Motor Company in any way. American Honda Motor Company does not sponsor, support, or endorse Honda-Tech.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.