Milky oil In my catch can
#1
Honda-Tech Member
Thread Starter
Join Date: Feb 2007
Location: Northern Cali, USA
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
Milky oil In my catch can
I have a turbo gsr in my EJ8
Wiscos 81.5mm (close piston to wall clearnce if it matters .0025in i think)
Im running the two block fittings
off the back and the catch can is draining back. when i pull off the filter to the catch can the oil that is settled in there is all milky (brightly)
Is this ok
Wiscos 81.5mm (close piston to wall clearnce if it matters .0025in i think)
Im running the two block fittings
off the back and the catch can is draining back. when i pull off the filter to the catch can the oil that is settled in there is all milky (brightly)
Is this ok
#2
Mr. Badwrench
Join Date: May 2002
Location: stranger in a strange land
Posts: 14,146
Likes: 0
Received 2 Likes
on
2 Posts
technically no, if it is draining back.
if it is an open element pcv system, it will pick up the moisture in the air.
is it milky under our valve cover? if not dont worry. maybe put a petcock on the drainback, and drain it when it gets full.
if it is an open element pcv system, it will pick up the moisture in the air.
is it milky under our valve cover? if not dont worry. maybe put a petcock on the drainback, and drain it when it gets full.
#3
Honda-Tech Member
Join Date: Feb 2003
Location: schooling kids in ny, usa
Posts: 9,813
Likes: 0
Received 9 Likes
on
9 Posts
i dont know if i'd want that oil getting back in my system. it contains gas and other stuff. i just empty my can and throw it out every so often. mine is open air no drainback, and it does get milky looking at the bottom
#6
Honda-Tech Member
Join Date: Mar 2006
Location: Newark, DE
Posts: 6,381
Likes: 0
Received 0 Likes
on
0 Posts
The milky filter is probably from outside moisture as stated above, and like Mikey said pull the valvecover and if its not milky under there I wouldnt worry. I dont see what the big deal is about draining back into the system, where do you think all those contaminates came from in the first place? If the stuff would of never made it into the can it would be in the engine anyway, I cant tell you what my can has in it its always empty and I run -12 lines so I dont think I push much oil at all, I change my oil every 1k miles or so and I am not worried about it. My oil does smell really contaminated when I do change it but it smelled that way then I just had an Endyn can with no drain back.
#7
Honda-Tech Member
Join Date: Sep 2006
Location: poopfacepartytime, ca, usa
Posts: 5,856
Likes: 0
Received 0 Likes
on
0 Posts
I used to have a non drain back setup and the can was full of milky oil, it filled up so fast and often i made it drain back and my oil is always crystal clear now!
Trending Topics
#8
Honda-Tech Member
Thread Starter
Join Date: Feb 2007
Location: Northern Cali, USA
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
Ok, I pulled my valve cover and looks normal!
I change my oil often and it looks like honney each time.
Sounds like everything is ok and i agree, I too think its from the atmosphere and hot oil.
Thanks for the replies+++
I change my oil often and it looks like honney each time.
Sounds like everything is ok and i agree, I too think its from the atmosphere and hot oil.
Thanks for the replies+++
#9
Honda-Tech Member
Join Date: Feb 2003
Location: schooling kids in ny, usa
Posts: 9,813
Likes: 0
Received 9 Likes
on
9 Posts
wrong and wrong. that **** is milky cause it stays in the can and gets exposed to moisture and blowby, if you two were right then your god damn oil would have been just as milky before you installed the catch can, you think you install a catch can then suddenly milky oil is being produced by your engine and the can catches it?
I used to have a non drain back setup and the can was full of milky oil, it filled up so fast and often i made it drain back and my oil is always crystal clear now!
I used to have a non drain back setup and the can was full of milky oil, it filled up so fast and often i made it drain back and my oil is always crystal clear now!
slow down dude. im perfectly aware that the catchcan oil looks milky because of condensation that occurs in the can, not because im mixing coolant in my oil in the motor and that combination is making its way into my catchcan. even if it has a drainback, condensation would still occur on the baffles in the can due to the temperature differences between the hotter can and the cooler air by the breather. I tought this to my 10th graders today, if you need a refresher you can come sit in on my class tomorrow.
with that being said, i wouldnt want the oil that now has water (caused by condensation) returning back into my engine. to each their own
#11
Honda-Tech Member
Join Date: Sep 2006
Location: poopfacepartytime, ca, usa
Posts: 5,856
Likes: 0
Received 0 Likes
on
0 Posts
slow down dude. im perfectly aware that the catchcan oil looks milky because of condensation that occurs in the can, not because im mixing coolant in my oil in the motor and that combination is making its way into my catchcan. even if it has a drainback, condensation would still occur on the baffles in the can due to the temperature differences between the hotter can and the cooler air by the breather. I tought this to my 10th graders today, if you need a refresher you can come sit in on my class tomorrow.
with that being said, i wouldnt want the oil that now has water (caused by condensation) returning back into my engine. to each their own
with that being said, i wouldnt want the oil that now has water (caused by condensation) returning back into my engine. to each their own
Thread
Thread Starter
Forum
Replies
Last Post
S2Carbonworks
Forced Induction
35
05-12-2010 10:19 AM