phelpsj2

I just got a wideband, and was wondering where you guys where getting ur 12v 10a source from and where you routed the white wire.

BigMike0147

I used an "add a circuit" under the dash that allows you to add another fuse off of one currently there. The white wire is for the signal going to an EMS, right?? If so, I wired that to an open spot in my ECU so that my Neptune could pick it up. Need to extend the wire.

SiRCiviC94

just get power from the fusebox under the dash theres 5 open slots...it would be good to run an inline fuse as well

phelpsj2

I heard to run the white wire to d10 or d14. d14 is the primary o2 sensor spot though. wont that not work

Whiterice-gsr

well the aem replacemnet would then become the primary o2 right?

racebum

solder a wire on a 10a fuse and find a switched power slot under the dash.

if you grind away a tiny bit of the plastic on the top side of a slide in fuse you'll have enough surface area for a good solder provided you use flux for a quick fuse

justYncredible

iTrader: (1)

hmm
anybody have any pictures of there setup?
i have the same aem wideband (currently not installed) but im going to run it separate from the oem o2 sensor

phelpsj2

a picture of the gauge mounted, or of the wiring? heres mine i mounted yesterday

justYncredible

iTrader: (1)

the wiring
mainly the fuse box area.
im not sure if mine is like yours since i have a 95 gsr

racebum

i just installed mine today

if you don't have running lights and fuse 16 is blank, take a spade off the hot side to an inline fuse holder then to the wideband

just in case anyone is searching in the future i mean fuse 16 for a 94-97 integra

justYncredible

iTrader: (1)

I'm sorry
But could you show a photo lol
I'm a visual learner
I'll have this one gauge being ran off this power source

phelpsj2

I finally wired mine up today, this is what i did. I got this fuse thing from discount autoparts and soldered my power wire to the fuse holder that i put in a spare fuse slot under the dash. then i put the ground behing the steering wheel.

rel

anyone got info on wiring the serial cable for datalogging?

BoostedDOHCGSR

for hondatas300 I wired mine up to d10. works great. Analog wire (white I believe)

EF1.8T

https://honda-tech.com/forums/engine-management-tuning-124/xenocron-com-write-up-diy-install-innovate-plx-aem-wideband-ems-3088834/

rel

i would love to hook to directly to my hulog

pkopalek

According to the AEM manual here: http://www.schnitzracing.com/manuals/AEMWBK.pdf you can set the configuration to the UEGO to P4, and use the white wire to plug into D14 of your ECU instead of your normal Narrowband O2 sensor.

HULOG should capture what the ECU is reading (since the reading will look like a normal nbo2 sensor to the ECU) and Crome Pro (or many of the other free softwares) should be able to plot that for you.

I'm about to try this today.

Muckman

iTrader: (2)

Technically correct but the resolution at 1v is horrible. It wont be any better than the stock O2. Look at the P4 graph.

wantboost

iTrader: (2)

Thread is old but I'll toss my hat in, having an AEM gauge type UEGO..

The white wire is a simulated analog 0-1v output, I would only hook uo that wir e if you're using a stock ecu and it needs the signal to not throw a cel/run like ****.

There's another loose wire that's a full 0-5v output. That's what gets connected in place of the oem o2 signal and the stock ecu will read 0-5v, assuming it's chipped. Your tuning software of choice should have a dropdown menu of o2 scalars. Select AEM and now your ecu will monitor real time o2 data and allow you to datalog the o2 info along with everything else.

There's no point in having a wideband if you can't connect it to your EMS of choice and monitor it as you definitely can't tune **** with a stock narrowband gauge.

Some engine management systems will even self tune the fuel map based off of the widebands 0-5v signal hooked up to it, you simply input an air fuel or lambda target value and as you drive the ecu will build a fuel map on its own.

pkopalek

Thanks for your reply.

I'm going to hook my AEM up to D14 and put it back into P0 mode (normal wideband 0-5v) for datalogging.

Having it on D10 doesn't work for Freelog or Crome anyway, and having it in P4 (simulated wideband) mode doesn't seem to help with that.

I have to say though, having the 02 sensor enabled is performing some impressive corrections during part-throttle driving, compared to disabling it (with the AEM connected as a narrowband simulated).

Going to just disable it though. Thanks again.