Where to find this type of connector for JDM turn signals?
#1
Honda-Tech Member
Thread Starter
iTrader: (1)
Join Date: Feb 2001
Location: FIND ME ON ******.COM
Posts: 1,595
Likes: 0
Received 0 Likes
on
0 Posts
Where to find this type of connector for JDM turn signals?
I'm looking for the harness connectors that fit into the turn signal sockets for the JDM headlights (shown above)
I can only think of 2 options (aside from just using generic female connectors directly on the pins):
1. pull some off of a jdm front clip
2. find another honda/acura vehicle that uses the same type of connector.
I have been looking through honda/acura parts catalogues online and so far, no luck.
Any help/suggestions?
#3
Honda-Tech Member
Thread Starter
iTrader: (1)
Join Date: Feb 2001
Location: FIND ME ON ******.COM
Posts: 1,595
Likes: 0
Received 0 Likes
on
0 Posts
Re: Where to find this type of connector for JDM turn signals? (teg97)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by teg97 »</TD></TR><TR><TD CLASS="quote">I used some usdm turn signal lights and made them fit, I can't think of the bulb number. Just match it up to a similar bulb and you will have to modify the bulb plastic where it screws in</TD></TR></TABLE>
sorry if my post was confusing...i dont need the actual BULB, i need the WIRING HARNESS connector that plugs into the piece shown in the picture
sorry if my post was confusing...i dont need the actual BULB, i need the WIRING HARNESS connector that plugs into the piece shown in the picture
#4
Honda-Tech Member
Join Date: Oct 2004
Location: NYOB, where is mah gun, USA
Posts: 1,435
Likes: 0
Received 0 Likes
on
0 Posts
Re: Where to find this type of connector for JDM turn signals? (JOHN WAYNE)
try password (leo) he is the chit when it comes to little tid bits like that
#5
Honda-Tech Member
Join Date: Mar 2001
Location: WV, USA
Posts: 8,119
Likes: 0
Received 0 Likes
on
0 Posts
Re: Where to find this type of connector for JDM turn signals? (JOHN WAYNE)
you should be able to modify a USDM one to fit into the turn signal houseing though. Or modify the housing to fit the US bulb holder.
I haven't seen that type of connector anywhere though.
I haven't seen that type of connector anywhere though.
#6
Honda-Tech Member
Join Date: Nov 2004
Location: ugh., WI, USA
Posts: 1,142
Likes: 0
Received 0 Likes
on
0 Posts
Re: Where to find this type of connector for JDM turn signals? (Erik95LS)
I just did this literally a week ago. I used the USDM bumper turn signal socket, the only part that doesn't work is one of the tabs on the light socket is a little too wide. I just took a small file and filed the jdm headlight notch a little wider to accomodate it. Works fine, they were a little hard to install, but I'd rather them be tight and not leak.
#7
Honda-Tech Member
Thread Starter
iTrader: (1)
Join Date: Feb 2001
Location: FIND ME ON ******.COM
Posts: 1,595
Likes: 0
Received 0 Likes
on
0 Posts
Re: Where to find this type of connector for JDM turn signals? (jvtec95)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by jvtec95 »</TD></TR><TR><TD CLASS="quote">I just did this literally a week ago. I used the USDM bumper turn signal socket, the only part that doesn't work is one of the tabs on the light socket is a little too wide. I just took a small file and filed the jdm headlight notch a little wider to accomodate it. Works fine, they were a little hard to install, but I'd rather them be tight and not leak. </TD></TR></TABLE>
thanks for the info...i might have to give that a shot
thanks for the info...i might have to give that a shot
Thread
Thread Starter
Forum
Replies
Last Post