I want to see if anyone is interested in helping me clean out my garage. I am currently not in the position to start shipping. If there is enough interest I should be able to start actual transactions soon.
Clutchmaster stage three clutch and pressure with an aluminum flywheel. They have plenty of life left in them. $450 + shipping.
http://lordgabe.homelinux.net/...l.JPG
http://lordgabe.homelinux.net/...p.JPG
d16z6 head ported with 15 ferrea stainless valves, a skunk2 camgear, and a zex 59300 cam. It also has a three angle valve job on the intake and a five angle on the exhaust side. my map sensor went out blowing one of the valves. It also needs two of the valve cover bolt holes retapped. This head pulled hard for N/A. Over $1000 invested selling for $300 + shipping.
http://lordgabe.homelinux.net/josh/d16z6head1.JPG
http://lordgabe.homelinux.net/josh/d16z6head2.JPG
LS rods peened to fit a d series engine with srp 9:1 comp pistons for d16 factory bore. $250 +shipping
http://lordgabe.homelinux.net/...s.JPG
D16y8 intake manifold with fuel rail no sensors $70 + shipping.
GSR throttle body with an OBDO map adapter $60 + shipping
Civic CX close cat Exhaust manifold. Perfect for a homemade turbo kit. $50 + shipping.
http://lordgabe.homelinux.net/josh/cxmani1.JPG
http://lordgabe.homelinux.net/josh/cxmani2.JPG
D16A6 short block. $75 + shipping
http://lordgabe.homelinux.net/josh/d16a6block.JPG
nuespeed 550cc injectors for 92 to 95 civcs. they need grommets and o-rings. $75 + shipping.
D-series Block gaurd. I don't remember what brand it is. $50 + shipping
http://lordgabe.homelinux.net/josh/blockgaurd.JPG
MSD RPM Switch with pills. New in box. $55 + shipping.
http://lordgabe.homelinux.net/josh/rpmswitch.JPG
PM6 ECU $50 + shipping.
http://lordgabe.homelinux.net/josh/pm6ecu.JPG
Feilds v-tec controller (sold)


Modified by cfcrxsisohcvtec at 6:43 PM 9/26/2004


Modified by cfcrxsisohcvtec at 12:12 AM 11/4/2004


Modified by cfcrxsisohcvtec at 4:11 PM 11/5/2004

 

ttt

 

will the lsd fit my si tranny?

 

it will fit any d-series tranny. But I think you have to get 90-93 integra axles to make it all work.

 

I also have a sony in dash minidisc changer for sale. $125+ shipping.

 

pm sent about pistons and rods.

 

ttt

 

ttt

 

ttt

 

PMed you

I'm ready to buy!

 

ttt

 

ttt

 

ttt

 

ttt

 

jaker, I haven't forgot about you I am working on getting the pics you requested.

 

ttt

 

ttt

 

ttt

 

PM and payment sent for that LSD.

 

ttt

 

Tell me a little more about the z6 head. Blown valve?

 

I beleive it had about 60K on it when I purchased it. I had a machine shop in my area port it and give it an angled valve job. They also freshened it up. They did a partial rebuild. In other words they replaced pretty much everything but the valve springs and retainers. the valve cover bolts gave loose later. I only put around 3K to 5K on the head myself and it made a dramatic difference in my performance while it lasted. I had intended to go forced induction with it. Now I am just looking to do a B-series swap so I have no need for this head. If there is anything else you would like to know feel free to ask. I can be contacted via e-mail at cny71057@centurytel.net Thanks.

 

ttt

 

Note in the picture of the d16z6 head the bottom left valve of the third combustion chamber from the left has got the hole in it. It will need a new valve and reseating.

 

ttt