16411-p73-000 ; stay, throttle wire (throttle cable bracket)
17910-st7-r01 ; wire, throttle (itr throttle cable)
16176-p30-004 ; throttle body gasket
11853-Pr3-000; (x2) this is the grommet on the charcoal caniseter that feeds from the oil from the block. the itr has 2 of the same sized grommet. gsr is 2 different sized

i would recomend getting the new itr box. that way everything fits like designed from honda.

i lost oil from one hole because the grommet did not put enough pressure onto the hose that lead into the box

dunno part # , but si fuel line (hose, fuel feed)

gsr one is a lil short, si gives more slack for running different types of intakes.

other main part needed is
itr or most civics bracket and throttle rotor that mounts to the throttle body. you cant just buy these from h/a by themselves. they are sold as one piece with the throttle cable.

hope this is helpfull for you all


[Modified by Bob-DC2, 9:11 AM 11/29/2002]


[Modified by Bob-DC2, 1:33 PM 2/21/2003]

 

If you want to save money you can make a bracket like the one in my post below.


https://honda-tech.com/zerothread?id=234963

 

just making sure some people see this

 

you might also get an si fuel cable

make sure to pick up new washers from the dealer!

 

thanks for the info..I was just about to buy the manifold....thanks for the tip...are you pleased with it? HP improved?

cheers,

YV

 

hmmm... if 17910-ST7-R01 is the itr throttle cable, then whats 17910-SK7-A03??? thats the cable mike k. sent me.

 

Hey Guys...just to clarify, the part number 17910-st7-r01 is inaccurate.

17910-sk7-a03 is correct..just an FYI.........total price for all three listed is $31.27 tax included.....not bad,

cheers,

YV

 

thats what i thought. thanks young.

then whats 17910-ST7-R01??? its a throttle cable, but for which car specificly?

 

my buddy that looked it up found that it was an invalid number....

cheers,

YV

 

hope you've got cams, v-afc, and maybe a little compression in with the mix.

you'll lose about 8hp in the mid range on an otherwise stock setup.

no doubt you know this though...it's moreso for the noobs

--

also, I believe you have to remount a couple of breather lines with this. (loosing the butterflies...)

 

here is a good link related to this project...

YV

http://www.jdmhondaparts.com/tech/sk2manifold/

 

i was able to cut a pie section out of my stock bracket bend it down and reweld it in place. works perfectly. and i cleand it up so it looks nice. wasn't that hard and it was my first time welding. but if you don't have a welder then you'll have to do it the other ways.

 

well, It is not perticulary wrong. ( I am never wrong of course)

in the acura dealer parts cd program. it lists it as 17910-ST7-R01

acura sometimes changes parts numbers

the SK7 is probably the older one. if you give either part #'s to the dealer they will both work fine

 

great info, i was actually going to post something asking exactly what i needed, is the Si fuel line necessary though? right now ive got the manifold and the itr bracket, so i will need the cable and the TB gasket right? any other mods needed to make it work? thanks
edit: oh and the tb rotor piece, that doesnt have a part #?


[Modified by mattL, 5:36 PM 11/29/2002]

 

depends upon what intake you are using. i am using the j's racing intake. it would not fit at all with the gsr fuel rail. i have heard some fitment issues with the aem and maybe comptech icebox. skunk2 said they run the iceman. i think they are totally stupid. because i know the aem most of the time does not work, and iceman is pretty similar

i would buy it before the install from the dealer, and then return it, if you dont end up using it.


thanks for the helpfull post buddy

well, since I have high CR, lumpy cams, and a good header/exhaust setup. it will gain more than "a few hp"

dont make stupid comments lame tard

 

an FYI bump

 

Shouldnt the Intake manifold gasket be replaced also? I see that you have TB gasket just thought Id add Intake mani gasket for good measure.

 

I am guessing you do not have to. but I got the hondata intake manifold gasket...

 

Where did you get an Acura part # cd program from? I need one of those and a Honda one 2.

 

anyone know if you need similar things with a jg victor x setup?

 

i can sell you an acura program. I know the owner of a acura and honda dealership

 

how much for both of those programs? Lets not meet where we met for the flywheel. haha

 

update!
more parts that skunk2 didnt tell its customers about because they were trying to sell their product as a simple bolt on piece, even though it is not at all.

 

I need these!

 

bah...i already bought the bracket, itr throttle cable, i have the bbk itb w/ a non-gsr pulley....but i didnt know i had to get this: 11853-Pr3-000; (x2) this is the grommet on the charcoal caniseter that feeds from the oil from the block. the itr has 2 of the same sized grommet. gsr is 2 different sized

how much does that cost? shouldnt be much..but damn...hopefully i get my manifold on this sunday!