Honda-Tech - Honda Forum Discussion
0 2019/09/12 20:08:15
0 2019/09/12 20:08:12
This area was pretty easy to get to. I just used a plastic removal tool and popped off the old plastic mounting screws. I believe there were 2 in the wheel well and 2 at the bottom.
This area was pretty easy to get to. I just used a plastic removal tool and popped off the old plastic mounting screws. I believe there were 2 in the wheel well and 2 at the bottom.
0 2019/09/12 20:08:09
0 2019/09/12 20:08:05
0 2019/09/12 20:08:03
Here it is. I'm not sure if the evap lines are the same on the hatch tank but I'll see tomorrow. If the line is on there it would mean you could just get the sensor and hook it up to the stock tank.
Here it is. I'm not sure if the evap lines are the same on the hatch tank but I'll see tomorrow. If the line is on there it would mean you could just get the sensor and hook it up to the stock tank.
0 2019/09/12 20:07:59
0 2019/09/12 20:07:56
0 2019/09/12 20:07:52
0 2019/09/12 20:07:48
I have a lot more fun driving this than I thought I would. I'm thinking about putting the LS swap in this instead of my EG.
I have a lot more fun driving this than I thought I would. I'm thinking about putting the LS swap in this instead of my EG.
0 2019/09/10 00:34:31
I think just pushing dents out by hand makes a big difference. I'm looking forward to working on this again.
I think just pushing dents out by hand makes a big difference. I'm looking forward to working on this again.
0 2019/09/10 00:33:38
0 2019/09/10 00:33:35
0 2019/09/10 00:33:32
0 2019/09/10 00:33:28
If I can't push these dents out with the new tools I'm just going to lay bondo over them and paint.
If I can't push these dents out with the new tools I'm just going to lay bondo over them and paint.
0 2019/09/09 23:28:25
0 2019/09/09 23:28:22
I'm going to attempt body work on this car. Bought a few tools to help push the dents out as much as possible. Hopefully I can get all the lines out with the new tools. I've already gone in and tried to remove as many dents as I could by hand. I could really only push them out a little bit but it made a pretty big difference.
I'm going to attempt body work on this car. Bought a few tools to help push the dents out as much as possible. Hopefully I can get all the lines out with the new tools. I've already gone in and tried to remove as many dents as I could by hand. I could really only push them out a little bit but it made a pretty big difference.
0 2019/09/09 23:28:18
0 2019/09/09 23:28:15
0 2019/09/09 23:28:11
I'm going to be restoring these and a set of spare headlights I have in a couple days.
I'm going to be restoring these and a set of spare headlights I have in a couple days.
0 2019/09/09 23:28:08
I'm getting some
I'm getting some
0 2019/09/09 23:28:04
0 2019/09/09 23:17:35
0 2019/09/09 23:17:31
A very big improvement over the original sagging headliner. I may have to take everything out to re-glue, re-position and or smooth out wrinkles. This wasn't a hard job and only cost me about $50.
A very big improvement over the original sagging headliner. I may have to take everything out to re-glue, re-position and or smooth out wrinkles. This wasn't a hard job and only cost me about $50.
0 2019/09/09 23:17:28
Not the best job on the first sun visor. I've got 3 more to work with though so I'll figure out what works best for me and let you guys know.
Not the best job on the first sun visor. I've got 3 more to work with though so I'll figure out what works best for me and let you guys know.
0 2019/09/09 23:15:38
0 2019/09/09 23:15:35
0 2019/09/09 23:15:32
0 2019/09/09 23:15:28
Be careful installing the new liner on the door panels. It's not easy to keep wrinkles out. I'll probably end up pulling these back out to pull the wrinkles when I install speakers. I used a light duty bonding spray from Elmer's that supposed to have a permanent hold. We'll see. I've ordered some more heavy duty glue just in case.
Be careful installing the new liner on the door panels. It's not easy to keep wrinkles out. I'll probably end up pulling these back out to pull the wrinkles when I install speakers. I used a light duty bonding spray from Elmer's that supposed to have a permanent hold. We'll see. I've ordered some more heavy duty glue just in case.
0 2019/09/08 23:10:16
0 2019/09/08 23:10:13
0 2019/09/08 23:10:10
0 2019/09/08 23:10:07
These plastic rivets are pretty easy to drill out. If you do it well you'll have a nice mount for a screw to put back in it's place. Just be careful when your mounting it with screws, you don't want to push into the other side. Totally not comfy to have a screw poking your arm
These plastic rivets are pretty easy to drill out. If you do it well you'll have a nice mount for a screw to put back in it's place. Just be careful when your mounting it with screws, you don't want to push into the other side. Totally not comfy to have a screw poking your arm
0 2019/09/08 23:10:04
0 2019/09/08 23:10:01
I'm sad that I didn't get a photo of the headliner with suede before I installed it. Oh well...
I'm sad that I didn't get a photo of the headliner with suede before I installed it. Oh well...
0 2019/09/08 23:09:58
I was able to pull everything out without pulling the seats or rear plastics and it actually only took me maybe 30 minutes. If I have to do this again I wouldn't be upset about it.
I was able to pull everything out without pulling the seats or rear plastics and it actually only took me maybe 30 minutes. If I have to do this again I wouldn't be upset about it.
0 2019/09/08 23:02:16
The armrest was two screws to pull off. I believe it's 6 screws to separate the two top pieces. This was the easiest part of the job in all aspects.
The armrest was two screws to pull off. I believe it's 6 screws to separate the two top pieces. This was the easiest part of the job in all aspects.
0 2019/09/08 23:02:12
0 2019/09/08 23:02:08
My dog Baxter was helping me hold down the back seat. He's a little camera shy.
My dog Baxter was helping me hold down the back seat. He's a little camera shy.
0 2019/09/08 23:02:05
0 2019/09/08 23:02:02