Honda-Tech - Honda Forum Discussion
J engine with K transmission parts
J engine with K transmission parts
0 2022/10/07 14:09:21
J series cylinder head parts
J series cylinder head parts
0 2022/10/06 14:01:07
0 2022/09/23 22:23:45
D16Z6 head bolt on left, and 625 plus 11mm x 1.5 SRT4 stud on the right.
D16Z6 head bolt on left, and 625 plus 11mm x 1.5 SRT4 stud on the right.
0 2022/09/08 14:44:14
4 AN hose at a 90degree bend going into a 0.065 restrictor.
4 AN hose at a 90degree bend going into a 0.065 restrictor.
0 2022/09/01 15:06:05
Tee, 1/8NPT to 4AN fittings then 4 AN hose with heat shield.
Tee, 1/8NPT to 4AN fittings then 4 AN hose with heat shield.
0 2022/09/01 15:05:58
Khumo road huggers (average) on GSR blades
Khumo road huggers (average) on GSR blades
0 2022/08/31 21:29:49
PTE 4831B and 3” V-band to 3” Go-Autoworks downpipe.
PTE 4831B and 3” V-band to 3” Go-Autoworks downpipe.
0 2022/08/31 21:28:28
Golden Eagle Manufacturing recommended break in for their sleeves.
Golden Eagle Manufacturing recommended break in for their sleeves.
0 2022/08/29 10:53:28
10mm, 11mm, 12.7mm (1/2”)
10mm, 11mm, 12.7mm (1/2”)
0 2022/08/20 08:12:03
See red arrow
See red arrow
0 2022/08/11 20:30:21
0 2022/08/04 08:15:40
0 2022/08/04 08:10:40
0 2022/08/04 08:10:14
0 2022/07/16 10:42:54
Assembly oil dripping out…
Assembly oil dripping out…
0 2022/06/27 16:35:08
See arrow and key spot on snout bit lined up.
See arrow and key spot on snout bit lined up.
0 2022/06/27 16:29:39
Cylinder 1 all the way up.
Cylinder 1 all the way up.
0 2022/06/27 16:27:00
Cam seal on all the way?
Cam seal on all the way?
0 2022/06/27 16:23:55
Cam seal on all the way?
Cam seal on all the way?
0 2022/06/27 16:23:49
$46 for a new one?
$46 for a new one?
0 2022/06/24 15:46:27
$46 for a new one?
$46 for a new one?
0 2022/06/24 15:46:22
Torque sequence
Torque sequence
0 2022/06/24 10:15:43
15-30-60ft/lbs in the sequence
15-30-60ft/lbs in the sequence
0 2022/06/24 10:11:51
0 2022/06/24 10:10:38
0 2022/06/24 10:09:30
Bolts seem more than tight enough, and there is no click from the torque wrench on 20 inch pounds or 35 inch pounds. I tried turning the torque ratchet counter clock wise and then clockwise again to see if if would click, but it didn’t. Maybe
Bolts seem more than tight enough, and there is no click from the torque wrench on 20 inch pounds or 35 inch pounds. I tried turning the torque ratchet counter clock wise and then clockwise again to see if if would click, but it didn’t. Maybe
0 2022/06/23 16:59:08
On 20 inch pounds, I also tried the next setting of 35 inch pounds which is only less than 3 foot pounds.
On 20 inch pounds, I also tried the next setting of 35 inch pounds which is only less than 3 foot pounds.
0 2022/06/23 16:57:12
Loosened the bottom knob by hand and the adjusted the torque wrench to 20 inch pounds, then tightened the knob
Loosened the bottom knob by hand and the adjusted the torque wrench to 20 inch pounds, then tightened the knob
0 2022/06/23 16:55:57
Honda-bond HT on the rear main seal bracket
Honda-bond HT on the rear main seal bracket
0 2022/06/23 16:54:52
0 2022/06/21 15:25:41
Stripped threads are on the hole with the bright colored washer.
Stripped threads are on the hole with the bright colored washer.
0 2022/06/20 16:21:15
Oil pan installed
Oil pan installed
0 2022/06/17 14:50:53
Oil pan bolt with nut on it replacing stripped thread on one oil pan spot.
Oil pan bolt with nut on it replacing stripped thread on one oil pan spot.
0 2022/06/17 14:44:14
Tial MV-S old springs on left and new ones on the right.
Tial MV-S old springs on left and new ones on the right.
0 2022/06/15 06:28:43
0 2022/06/11 10:38:19
0 2022/06/11 10:38:13
Both bolt holes are ok though
Both bolt holes are ok though
0 2022/06/09 14:15:27
Scraped/ broken chunk off the engine block
Scraped/ broken chunk off the engine block
0 2022/06/09 14:15:21
Gouge in packaging on the side of the D16Y7
Gouge in packaging on the side of the D16Y7
0 2022/06/09 14:12:59