Honda-Tech - Honda Forum Discussion
0 2022/09/29 06:28:08
0 2022/09/29 06:28:00
0 2022/09/29 06:16:14
0 2022/09/29 06:15:54
0 2022/09/29 06:11:49
0 2022/09/29 06:09:44
0 2022/09/29 06:08:20
Frankenstein axle - 87 Accord passenger axle with DC Integra driver axle inner joint.
Frankenstein axle - 87 Accord passenger axle with DC Integra driver axle inner joint.
0 2022/09/19 18:25:00
Franken-axle installed on the driver's side of my Civic with the hydro ZC half shaft.
Franken-axle installed on the driver's side of my Civic with the hydro ZC half shaft.
0 2022/09/19 18:24:51
Top is 87 Accord passenger axle, bottom is DC Integra driver axle, both with inner joint removed.
Top is 87 Accord passenger axle, bottom is DC Integra driver axle, both with inner joint removed.
0 2022/09/19 18:24:44
0 2022/09/18 17:28:19
0 2022/09/18 13:15:39
0 2022/09/18 13:15:33
0 2022/09/18 13:14:52
0 2022/09/11 12:09:29
0 2022/08/30 07:10:59
0 2022/08/09 07:34:57
0 2022/06/02 13:26:59
0 2022/03/07 12:41:45
0 2022/01/27 05:58:55
0 2021/12/22 15:24:06
0 2021/12/20 11:22:39
0 2021/12/18 11:41:50
0 2021/08/08 15:05:16
0 2021/08/08 15:05:14
0 2021/02/10 11:56:00
0 2021/02/09 17:59:44
0 2021/01/15 10:43:32
0 2021/01/15 10:37:16
0 2021/01/03 15:58:39
0 2020/12/06 16:44:38
0 2020/12/06 16:44:34
0 2020/11/25 15:00:44
0 2020/10/21 13:36:04
You can probably get away with just using a rubber cap, but I cut off the coolant nipple here where the small coolant line came from, tapped it, and threaded in an bolt with Permatex Ultra Grey on the threads - never had an issue with it like this.
You can probably get away with just using a rubber cap, but I cut off the coolant nipple here where the small coolant line came from, tapped it, and threaded in an bolt with Permatex Ultra Grey on the threads - never had an issue with it like this.
0 2020/10/06 12:15:34
Here is the block-off plate installed. I just cut off the nipple where the coolant hose went into the TB to clean up the look since I wasn't using it anymore. I just removed the lower portion of the IACV (not pictured) where the coolant ports attached.
Here is the block-off plate installed. I just cut off the nipple where the coolant hose went into the TB to clean up the look since I wasn't using it anymore. I just removed the lower portion of the IACV (not pictured) where the coolant ports attached.
0 2020/10/06 12:15:29
0 2020/07/20 17:26:22
0 2020/07/20 17:26:20
0 2020/07/20 16:08:15
0 2020/07/20 09:47:24