Honda-Tech - Honda Forum Discussion
0 2019/12/09 11:04:44
0 2019/12/09 11:04:36
0 2019/12/09 11:00:42
0 2019/12/09 11:00:34
0 2019/12/09 11:00:25
0 2019/12/09 11:00:16
0 2019/12/09 10:59:32
0 2019/12/09 10:59:20
0 2019/12/09 10:59:08
0 2019/12/09 10:59:00
I threw up in my mouth a bit there. But....Moving on.
I threw up in my mouth a bit there. But....Moving on.
0 2019/11/13 21:18:40
0 2019/11/04 07:20:00
The Coolant only becomes heated during shut down during the CHRA's siphoning effect of the heat from the the turbine housing.
The Coolant only becomes heated during shut down during the CHRA's siphoning effect of the heat from the the turbine housing.
0 2019/10/09 20:48:28
0 2019/09/03 07:36:42
0 2019/08/15 21:50:57
0 2019/07/09 20:48:09
0 2019/07/09 20:42:43
0 2019/07/09 20:41:58
0 2019/07/09 20:41:26
0 2019/07/02 20:11:28
0 2019/06/27 14:44:35
Horrible drainage.. I saw a lot of problems in this style.
Horrible drainage.. I saw a lot of problems in this style.
0 2019/06/19 17:16:11
0 2019/06/19 17:14:51
This has a decent chance of a good drain, but hard to see any additional bends on 1 & 4. Notice how the wastegate placement is completely fine
This has a decent chance of a good drain, but hard to see any additional bends on 1 & 4. Notice how the wastegate placement is completely fine
0 2019/06/19 17:12:33
Notice the additional bends on 1 & 4, it brings up the Turbine inlet flange up easily an inch or so for better drain
Notice the additional bends on 1 & 4, it brings up the Turbine inlet flange up easily an inch or so for better drain
0 2019/06/19 17:11:18
This sits much higher even in the H22A
This sits much higher even in the H22A
0 2019/06/19 17:09:31
0 2019/06/19 17:08:33
You can almost see the turbocharger from the engine bay itself since it sits higher.
You can almost see the turbocharger from the engine bay itself since it sits higher.
0 2019/06/19 17:02:33
From the side, you can see how runners 1 & 4 have a slight additional bend in them to allow the turbocharger to sit a bit higher for better drain flow
From the side, you can see how runners 1 & 4 have a slight additional bend in them to allow the turbocharger to sit a bit higher for better drain flow
0 2019/06/19 17:00:21
Notice how the bends on 1 & 4 pull the turbine inlet flange a bit higher than most, allowing for a proper drain
Notice how the bends on 1 & 4 pull the turbine inlet flange a bit higher than most, allowing for a proper drain
0 2019/06/19 16:58:28
0 2019/06/18 15:48:29
0 2019/06/18 15:46:17
0 2019/06/18 15:42:28
0 2019/06/18 15:41:33
0 2019/06/18 15:40:36
0 2019/06/18 15:39:16
0 2019/06/18 15:38:23
0 2019/05/27 21:00:57
0 2019/05/27 20:59:06
TR3030R VelociRaptor MKIII Side
TR3030R VelociRaptor MKIII Side
0 2019/05/23 06:20:06