Honda-Tech - Honda Forum Discussion
Homecoming.
Homecoming.
0 2015/04/03 18:13:59
0 2015/04/03 18:24:25
0 2015/04/03 18:24:29
0 2015/04/03 18:24:32
0 2015/04/03 18:28:06
0 2015/04/03 18:29:19
0 2015/04/04 18:23:44
0 2015/04/04 18:24:40
0 2015/04/04 18:28:53
0 2015/04/04 18:32:03
0 2015/04/04 18:35:06
0 2015/04/04 18:35:18
0 2015/04/04 18:35:27
0 2015/04/06 21:41:34
Injector clips
Injector clips
0 2015/04/06 21:42:08
Mock up
Mock up
0 2015/04/06 21:42:27
So fresh and so clean
So fresh and so clean
0 2015/04/13 19:27:57
Love this view
Love this view
0 2015/04/13 19:28:01
My little helper
My little helper
0 2015/04/13 19:28:04
Complete valve cover gasket set, new NGK plugs and wire. Highend header looking so fresh and so clean.
Complete valve cover gasket set, new NGK plugs and wire. Highend header looking so fresh and so clean.
0 2015/04/13 19:33:03
Euro-R single crank pulley
Euro-R single crank pulley
0 2015/04/13 19:33:09
My little helper
My little helper
0 2015/04/13 19:33:13
Installed
Installed
0 2015/04/22 07:59:26
Side by side
Side by side
0 2015/04/22 08:00:04
New bar
New bar
0 2015/04/22 08:00:34
Tight fit.
Tight fit.
0 2015/06/08 22:52:00
I used Aeroquip teflon -3an braided lines with Aeroquip stainless fittings. (I PERSONALLY don't like the blue/red aluminum fittings, stainless is much cleaner looking.) I also don't like mix and match, so I tried to stick with one brand (Aeroquip) for all my lines, fuel included.
I used Aeroquip teflon -3an braided lines with Aeroquip stainless fittings. (I PERSONALLY don't like the blue/red aluminum fittings, stainless is much cleaner looking.) I also don't like mix and match, so I tried to stick with one brand (Aeroquip) for all my lines, fuel included.
0 2015/06/08 22:52:41
Clutch disc.
Clutch disc.
0 2015/06/08 22:52:53
I got too excited to install the flywheel that I FORGOT to install the pilot bearing after I already Loctite and torqued bolts. Yeah, pain in the ass to remove and reinstall.
I got too excited to install the flywheel that I FORGOT to install the pilot bearing after I already Loctite and torqued bolts. Yeah, pain in the ass to remove and reinstall.
0 2015/06/08 22:52:58
Clutch line from master...
Clutch line from master...
0 2015/06/08 22:53:05
Installed.
Installed.
0 2015/06/08 22:53:10
Out with the old, in with the new.
Out with the old, in with the new.
0 2015/06/08 22:53:16
Pressure plate.
Pressure plate.
0 2015/06/08 22:53:21
Reservoir.
Reservoir.
0 2015/06/08 22:53:27
...to bulkhead.
...to bulkhead.
0 2015/06/08 22:53:33
Finally, assembled. Don't mind the crappy red intake pipe hose, its temporary until I decide what to do with a real intake setup. Advice and tips always helpful.
Finally, assembled. Don't mind the crappy red intake pipe hose, its temporary until I decide what to do with a real intake setup. Advice and tips always helpful.
0 2015/06/08 23:04:15
line from master
line from master
0 2015/06/10 20:05:12
dash removal is not required, although HIGHLY recommended. It is a tight fit.
dash removal is not required, although HIGHLY recommended. It is a tight fit.
0 2015/06/10 20:05:15
Everything lines up perfectly, no modifications required.
Everything lines up perfectly, no modifications required.
0 2015/06/10 20:05:18
Reservoir installed
Reservoir installed
0 2015/06/10 20:05:22