Honda-Tech - Honda Forum Discussion
Just a random current shot
Just a random current shot
0 2013/08/28 05:22:41
imag0088b
imag0088b
0 2011/11/17 19:19:40
imag0143u
imag0143u
0 2011/11/17 19:19:40
IMAG0144
IMAG0144
0 2011/08/15 12:56:46
0 2013/05/07 16:26:33
sdc10088w
sdc10088w
1 2012/02/19 10:05:08
IMG 0014
IMG 0014
0 2011/08/15 12:56:46
0 2013/06/16 21:41:30
sdc10101s
sdc10101s
0 2011/11/16 19:00:34
0 2012/04/13 20:02:22
Still in the process of cleaning up the bay
Still in the process of cleaning up the bay
0 2013/05/07 16:26:33
0 2013/06/16 21:41:30
0 2013/06/15 03:24:42
When I have an extra 200 in my pocket, a PWDJDM 4 point will be there. Till then, this is in use.
When I have an extra 200 in my pocket, a PWDJDM 4 point will be there. Till then, this is in use.
3 2012/02/19 10:05:08
0 2013/06/15 03:24:42
Progress so far
Progress so far
0 2013/06/12 12:21:22
0 2013/06/15 03:24:42
Nevermind the arm rest, i fixed it.
Nevermind the arm rest, i fixed it.
0 2012/02/19 10:05:08
Getting tuned by Turbogixxer Kenny @ P2R power rev racing
Getting tuned by Turbogixxer Kenny @ P2R power rev racing
0 2012/02/19 10:07:21
0 2013/06/16 21:41:30
0 2013/06/12 12:21:22
Yea thats me in the pits at Homestead Speedway. Got to drive brand new Audi's around the track.
Yea thats me in the pits at Homestead Speedway. Got to drive brand new Audi's around the track.
0 2012/04/14 14:17:47
9/7/13
9/7/13
0 2013/09/07 16:15:00
The build that never was. Silver Surfer. After ripping everything apart for piston upgrade, found cracked sleeve.
The build that never was. Silver Surfer. After ripping everything apart for piston upgrade, found cracked sleeve.
2 2012/09/14 23:43:51
new pistons
new pistons
3 2012/10/29 00:22:26
Got the engine all spec'd and ready to go. 84mm ITR reps, resized rods w/ ARP, ARP studs, ACL bearings in spec .0015, P8R head polished with gasket match, Crane 0016 cams.
Got the engine all spec'd and ready to go. 84mm ITR reps, resized rods w/ ARP, ARP studs, ACL bearings in spec .0015, P8R head polished with gasket match, Crane 0016 cams.
0 2012/11/09 14:53:21
block cleaned and painted
block cleaned and painted
0 2012/11/13 20:13:46
cleaned/painted Alt mount and Alt
cleaned/painted Alt mount and Alt
0 2012/11/13 20:13:46
Crane 0016 Cams Dur 274 / 274 Dur@50 218/218 LSA 108 Lift 433/433
Crane 0016 Cams Dur 274 / 274 Dur@50 218/218 LSA 108 Lift 433/433
8 2012/11/13 20:16:31
Head is on
Head is on
0 2012/12/09 17:30:14
Got the cams dialed in at '0', lash set, in time, VC on
Got the cams dialed in at '0', lash set, in time, VC on
0 2013/04/26 22:43:50
Trans gettin some fresh paint along with the new sync/sleeve install
Trans gettin some fresh paint along with the new sync/sleeve install
0 2013/04/26 22:43:50
Flywheel and new pilot in
Flywheel and new pilot in
0 2013/04/26 22:43:50
New Exedy clutch installed
New Exedy clutch installed
0 2013/04/26 22:43:50
Modded S2 Cam gear I used grade 5 bolts that were longer (cant remember the exact size) threaded thru backside and used red loctite. Then washers and lock nuts.
Modded S2 Cam gear I used grade 5 bolts that were longer (cant remember the exact size) threaded thru backside and used red loctite. Then washers and lock nuts.
1 2013/05/07 16:26:33
New Avid Mounts
New Avid Mounts
0 2013/05/07 16:26:33
0 2014/01/17 13:29:21