Honda-Tech - Honda Forum Discussion
0 2018/10/30 13:04:26
Before
Before
0 2018/10/30 13:11:55
After 2mm removed/ tapered bored like LHT
After 2mm removed/ tapered bored like LHT
0 2018/10/30 13:12:12
Blower inlet
Blower inlet
0 2018/10/30 13:12:23
Cleaned up the S-tube again and ported the blower inlet
Cleaned up the S-tube again and ported the blower inlet
0 2018/10/30 13:12:36
Port matched
Port matched
0 2018/10/30 13:12:57
A mild 3mm porting on each side of the blower outlet / I may do a more aggressive porting later like MR. GRiMM (RIP)
A mild 3mm porting on each side of the blower outlet / I may do a more aggressive porting later like MR. GRiMM (RIP)
0 2018/10/30 13:13:07
0 2018/10/30 13:18:44
0 2018/11/09 11:20:19
wot
wot
0 2018/11/09 11:20:32
74mm tapered to 68mm
74mm tapered to 68mm
0 2018/11/09 11:20:43
holley 68mm tb vs 74mm ebay special
holley 68mm tb vs 74mm ebay special
0 2018/11/09 11:20:56
74mm compared to the 68mm tb
74mm compared to the 68mm tb
0 2018/11/09 11:21:17
0 2019/01/11 14:47:31
0 2019/01/11 14:47:45
0 2019/01/11 14:47:58
throw out bearing
throw out bearing
0 2019/03/26 17:16:53
0 2019/03/26 17:16:58
0 2019/03/26 17:17:05
0 2019/03/26 17:17:10
4runner cargo cover
4runner cargo cover
0 2019/03/26 17:17:15
4runner cargo cover
4runner cargo cover
0 2019/03/26 17:17:21
Input shaft bearing
Input shaft bearing
0 2019/03/26 17:17:26
0 2019/05/23 17:23:33
0 2019/05/23 17:23:38
0 2019/05/23 17:24:27
0 2019/05/23 17:24:32
0 2019/05/23 17:26:06
0 2019/05/23 17:26:07
0 2019/05/23 17:30:01
0 2020/06/11 22:35:14
0 2020/06/11 22:35:30
0 2020/06/18 21:10:21
I could have tucked it up higher but I wanted a little more airflow between the oil pan.
I could have tucked it up higher but I wanted a little more airflow between the oil pan.
0 2020/06/18 21:10:43
0 2020/06/18 21:11:05
Added a small resonator right after the spun high flow cat.
Added a small resonator right after the spun high flow cat.
0 2020/06/18 21:11:39
My header design version the modified kamikaze header. 2" primaries vs 1 7/8"
My header design version the modified kamikaze header. 2" primaries vs 1 7/8"
0 2020/06/18 21:12:25
My welds are starting to look decent
My welds are starting to look decent
0 2020/06/18 21:12:52
0 2020/06/22 16:36:27
0 2020/06/30 12:56:53