preping the engine bay?
Joined: Sep 2003
Posts: 102
Likes: 0
From: TIJEEKASTAN
Re: preping the engine bay? (BLUE EH3)
take the harness off the motor completly... remove anything not pertaining to the motor swap.... first mount u wanna bolt onto the MOTOR is the rear bracket to the block !!!!!! then align it into th mount... then do the timin belt mount then the trans mount then the 2 mounts on the side...
MAKE SURE THE REAR BRACKET IS ON THE MOTOR FIRST... LOWER IT ON TO THE MOUNT... ur life will be so much easier that way
MAKE SURE THE REAR BRACKET IS ON THE MOTOR FIRST... LOWER IT ON TO THE MOUNT... ur life will be so much easier that way
Thread Starter
Help we my pennies
Joined: Jul 2003
Posts: 5,411
Likes: 0
From: 08854, NJ
Re: preping the engine bay? (Gsr_Hybrid_theory)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Gsr_Hybrid_theory »</TD></TR><TR><TD CLASS="quote">take the harness off the motor completly... remove anything not pertaining to the motor swap.... first mount u wanna bolt onto the MOTOR is the rear bracket to the block !!!!!! then align it into th mount... then do the timin belt mount then the trans mount then the 2 mounts on the side...
MAKE SURE THE REAR BRACKET IS ON THE MOTOR FIRST... LOWER IT ON TO THE MOUNT... ur life will be so much easier that way </TD></TR></TABLE> harness?
i guess i said it wrong, what should be done b4 u drop the motor in?
MAKE SURE THE REAR BRACKET IS ON THE MOTOR FIRST... LOWER IT ON TO THE MOUNT... ur life will be so much easier that way
</TD></TR></TABLE> harness?i guess i said it wrong, what should be done b4 u drop the motor in?
Honda-Tech Member
Joined: Jul 2001
Posts: 1,510
Likes: 0
From: Bellingham, WA, USA
Re: preping the engine bay? (BLUE EH3)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BLUE EH3 »</TD></TR><TR><TD CLASS="quote"> harness?
i guess i said it wrong, what should be done b4 u drop the motor in?</TD></TR></TABLE>
he meant wiring harness.
You dropping the tranny in at the same time as the motor, I assume? Well then, I would change the tranny fluid while the thing is out.
I personally, would install anything you can onto the engine while it's out. Intake manifold included.
i guess i said it wrong, what should be done b4 u drop the motor in?</TD></TR></TABLE>
he meant wiring harness.
You dropping the tranny in at the same time as the motor, I assume? Well then, I would change the tranny fluid while the thing is out.
I personally, would install anything you can onto the engine while it's out. Intake manifold included.
Honda-Tech Member
Joined: Sep 2003
Posts: 4,196
Likes: 0
From: Bluffton/Hilton Head,SC / Ft. Lauderdale, FL, usa
Re: preping the engine bay? (martini)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by martini »</TD></TR><TR><TD CLASS="quote">
I personally, would install anything you can onto the engine while it's out. Intake manifold included.</TD></TR></TABLE>
install the engine harness on the motor before u drop in the motor...just be careful not to crush any plugs when lowering it in.
I personally, would install anything you can onto the engine while it's out. Intake manifold included.</TD></TR></TABLE>
install the engine harness on the motor before u drop in the motor...just be careful not to crush any plugs when lowering it in.
Thread
Thread Starter
Forum
Replies
Last Post
ConceptVBS
Honda Civic (2001 - 2005)
4
Apr 17, 2014 06:14 AM
endo617
Honda CRX / EF Civic (1988 - 1991)
11
Jun 28, 2008 12:18 AM