Engine Question
Thread Starter
Joined: Jan 2005
Posts: 13
Likes: 0
Engine Question
hey i'm adjusting the valves on a f22b1... i start off by rotating the camshaft pulley until it says 'UP" at the very top.
i adjusted first the exhaust valves and then the intake valves according to spec.
then according to instructions i rotate the camshaft pulley 90 degrees counter-clockwise until the UP mark is on the left side, pointing towards the car's windshield...
according to instructions here i'm supposed to proceed adjusting the 3rd piston's valves... but (unlike the first piston's valves) i checked the valve clearances FIRST before adjusting them, and i can barely even fit a .003 feeler in there...
if the valves are that far off spec, wouldnt they have burnt up or something by now? or am i just doing something wrong? or am i totally right and need to go ahead and adjust them back to spec?
thanks guys.
i adjusted first the exhaust valves and then the intake valves according to spec.
then according to instructions i rotate the camshaft pulley 90 degrees counter-clockwise until the UP mark is on the left side, pointing towards the car's windshield...
according to instructions here i'm supposed to proceed adjusting the 3rd piston's valves... but (unlike the first piston's valves) i checked the valve clearances FIRST before adjusting them, and i can barely even fit a .003 feeler in there...
if the valves are that far off spec, wouldnt they have burnt up or something by now? or am i just doing something wrong? or am i totally right and need to go ahead and adjust them back to spec?
thanks guys.
Joined: Apr 2003
Posts: 1,342
Likes: 0
From: lewiston, maine, usa
Re: Engine Question (Hey Whats Up)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Hey Whats Up »</TD></TR><TR><TD CLASS="quote">i adjusted first the exhaust valves and then the intake valves according to spec. </TD></TR></TABLE>
Did you do all the valves before you rotated your cam gear 90 degrees?
Did you do all the valves before you rotated your cam gear 90 degrees?
Thread Starter
Joined: Jan 2005
Posts: 13
Likes: 0
Re: Engine Question (civic-4-ges)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by civic-4-ges »</TD></TR><TR><TD CLASS="quote">Did you do all the valves before you rotated your cam gear 90 degrees?</TD></TR></TABLE>
all the 4 valves on the 1st cylinder (exhaust and intake)
all the 4 valves on the 1st cylinder (exhaust and intake)
Honda-Tech Member
Joined: Sep 2001
Posts: 1,200
Likes: 0
From: Toronto, On, Canada
Re: Engine Question (Hey Whats Up)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Hey Whats Up »</TD></TR><TR><TD CLASS="quote">
then according to instructions i rotate the camshaft pulley 90 degrees counter-clockwise until the UP mark is on the left side, pointing towards the car's windshield...
thanks guys.</TD></TR></TABLE>
Your suppose to turn the crank 180 degrees counter clock wise(the camshaft will turn 90 degrees) and the UP marks will be facing the front(9 o'clock) of the motor not the windshield. Then adjust the number 3 clyinder.
"UP" mark:
cly.1 - 12 o'clock
cly.3 - 9 o'clock
cly.4 - 6 o'clock
cly.2 - 3 o'clock
then according to instructions i rotate the camshaft pulley 90 degrees counter-clockwise until the UP mark is on the left side, pointing towards the car's windshield...
thanks guys.</TD></TR></TABLE>
Your suppose to turn the crank 180 degrees counter clock wise(the camshaft will turn 90 degrees) and the UP marks will be facing the front(9 o'clock) of the motor not the windshield. Then adjust the number 3 clyinder.
"UP" mark:
cly.1 - 12 o'clock
cly.3 - 9 o'clock
cly.4 - 6 o'clock
cly.2 - 3 o'clock
Thread
Thread Starter
Forum
Replies
Last Post
ichikers
All Motor / Naturally Aspirated
13
Jan 15, 2007 04:43 PM
