Has anybody here put a 6 pt. roll cage in a del sol before? They don't make anything for a del sol.

Can you post pics?

Thanks

 

Who is "they"? Did you try Autopower in San Diego?

 

I meant there is no kits for a Del Sol.

Checked thier website, they don't have anything for a Del Sol.



Modified by Motorhead_AZ at 8:02 AM 9/12/2004

 

Anybody??

 

I did a 10point out of cro-mo in a Del Sol, all custom, I;ll try and post pics later, don't have them right now

 

Thanks for your response. 10 point would be an overkill for my setup, but I would very appericiate the pics.

Thanks again.

 

it was a pain, theres not much room to work, but just forget about the halo and a-piller bars and its the same

 

What's the minimum requirement for NHRA? isn't it a 6 pt?

 

Modified by b18cls1 at 7:48 PM 10/27/2003


this is one i did a long time ago

 

I guess there is no way to fit a 6 pt. in there without ripping the intrior appart.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Motorhead_AZ &raquo;</TD></TR><TR><TD CLASS="quote">I guess there is no way to fit a 6 pt. in there without ripping the intrior appart.</TD></TR></TABLE>

quitters never win, and winners never quit.


get creative, get off your butt, and go to an actual fab shop.

 

Go to Full-Race, they're there in the PHX area


Full-Race Motorsports
4107 E Winslow
Suite B
Phoenix, AZ 85040
(602) 437-2101

 

go-to racing has a del sol cage they have a del sol with a 6 point in it they built it too

 

I have one i have one!!! Give me a bit to get pix up

 

Everything still works, i only need to cut the bottom corner pannel on each side to get them in. The seats are just sitting in there loose... Cage is NHRA legal.
From my cardomain site (link in my sig):
Well, the cage is finally done and its actually legal. Somehow we managed to get about a 33* angle on the down bars on the back (minimun is 30), but had to cut into the back wall piece. I got NHRA legal swing outs for both sides. Both bars have pins at the bottom and top so you can either climb over, pull the top pin and swing the bar out, or pull both pins, remove the bar, and put it in the turnk or whatever. The seats are just sitting in there so the pass seat would come forward a little and not be right under that bar. The drivers seat is lined up where they will both be. Anyway, here it is...
PS: heading to paint this week (thats the plan anyway)

 

The worlds quickest street class del sol has a cage. I dont remember his SN but his name is jasen pennman, from utah i think. Ask him to post some pics of his car.

 

The boys at lockwood racing have a RR delsol that runs with NASA. Its very well built. Here is a link to their site.

http://www.lockracewrks.com/Ou....html

 

Cusco makes a 4pt & 6pt for the Del Sol.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by DelSolSiR &raquo;</TD></TR><TR><TD CLASS="quote">Cusco makes a 4pt & 6pt for the Del Sol.</TD></TR></TABLE>

Too bad it is discontinued.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by JDMCRXDelSol &raquo;</TD></TR><TR><TD CLASS="quote">
Too bad it is discontinued.</TD></TR></TABLE>

Actually http://www.sportcarmotion.com can get them direct from Japan, the 4pt is gonna be my next addition...