I just got my wing, and I was wondering if anyone could post pics of their install or anything. We were holding the wing up to the back, and it looks like it is too wide for the car. I think it might just be up there wrong, but I just wanted to make sure. Also, it bolts on by 2 bolts on each side right?

 

try http://www.riceboypage.com

j/k dude.

IM Skunk2nr, he has an ITR wing.

 

Thanks. But I just don't like the wingless look. And the GSR wing is dumb looking.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by IntegraBoy04 &raquo;</TD></TR><TR><TD CLASS="quote">Thanks. But I just don't like the wingless look. And the GSR wing is dumb looking. </TD></TR></TABLE>

I like my gsr wing think its clean and i don't think it calls for all that much attention. i'd rather have the attention in other places that matter like the engine....bet u wish you had vtec and some more ponies kickin around

 

Ok, well I don't like the look of it. And about the whole VTEC thing, I could care less. I like my LS.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by IntegraBoy04 &raquo;</TD></TR><TR><TD CLASS="quote">Ok, well I don't like the look of it. And about the whole VTEC thing, I could care less. I like my LS.</TD></TR></TABLE>

Don't worry, VTEC is overrated anyway. I thought elitists exists only in the ITR forum and not here.
I hope I can help but my car is pretty much stock exterior wise except for the OEM kit and rims.

 

Try the manufacturer's webpage if you can't figure it out. I can't see a simple 'install' like this needing a how-to guide.

 

The OEM ITR wing is held on by 2 bolts on each side. That is going to leave one hole on each side open which your are going to have to get filled or plugged.

 

Hey, i just went through the same thing with my car. I changed from the gsr wing to the type r wing. Be prepared to have some body work done to the trunk lid, i thought that the holes should line up for each wing but they dont. The gsr wing bolts in closer together than the type r wing, I had to fill the gsr holes, sand and redrill holes for the type r wing. What made this even worse was that we didnt realize this untill after the trunk had already been painted. So we got to do it all over again. Just plan ahead!!!

 

I don't have a wing at all right now. But thanks for the info.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by jl74 &raquo;</TD></TR><TR><TD CLASS="quote">Don't worry, VTEC is overrated anyway. </TD></TR></TABLE>
DAMN straight!!! look at the sig

 

[QUOTE=patdemps]

I like my gsr wing think its clean and i don't think it calls for all that much attention. i'd rather have the attention in other places that matter like the engine

 

you should get a 3 piece spoiler.. it looks better

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by integraguy2001 &raquo;</TD></TR><TR><TD CLASS="quote">you should get a 3 piece spoiler.. it looks better</TD></TR></TABLE>

 

the spoiler should bolt onto the trunk lid. if it doesnt, i'd check to see if the spoiler was meant for your make and model.

 

Thanks for all the help guys. I found out that he sent me the 4 door spoiler. So I am getting a new one.

 

oh man the three piece spoiler is such an ugly piece of crap, it looks like a pile of **** on the rear hatch.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 2kGS &raquo;</TD></TR><TR><TD CLASS="quote">oh man the three piece spoiler is such an ugly piece of crap, it looks like a pile of **** on the rear hatch.</TD></TR></TABLE>

yes they do. what a good statement. i fully agree!

 

if you do bolt on the itr wing make sure you put on some beefy washers.. i got mine ripped off a month ago.... they ripped the bolts out with the spoiler..
now i'm out 200 for the spoiler and another 1000? for the trunk lid

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by patdemps &raquo;</TD></TR><TR><TD CLASS="quote">i'd rather have the attention in other places that matter like the engine....bet u wish you had vtec and some more ponies kickin around </TD></TR></TABLE>

You're an idiot...


<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Peter K &raquo;</TD></TR><TR><TD CLASS="quote">if you do bolt on the itr wing make sure you put on some beefy washers.. i got mine ripped off a month ago.... they ripped the bolts out with the spoiler..
now i'm out 200 for the spoiler and another 1000? for the trunk lid </TD></TR></TABLE>

I've seen pictures of that. That sucks man, it's not a pretty site. They're actually that easy to rip off? (ITR wings)

I would suggest to cover the holes when going from a GS-R to an ITR fin by using vinyl. Go to a graphics shop and get the color of your car (white, silver, black, red etc.) on a sheet of vinyl. Cut it and cover the holes. No one will notice unless they get very very close, and it saves lots of $ in the meantime.