VA 600hp CRX "street legal" Race Car
Thread Starter
Honda-Tech Member
Joined: Aug 2009
Posts: 5
Likes: 0
600hp CRX "street legal" Race Car
1988 Honda CR-X Turbo 600HP * 10.21@140MPH
Extra Parts
2xMH slicks 8.5x24.5 on 2 extra 15 inch Enkei RP F1 (6 total rims and tires)
Steering wheel mounted remote Hi/Lo boost switch
Haltech E6K Stand Alone Engine Management with Sony Viao laptop with program loaded for tuning
MSD 3 Step launch control with 10 different RPM "pills"
Transmission Scatter shield
Dyno'd at 602whp @ 30psi
READ: While dyno tuning the boost spiked to 32+psi and crushed the number 4 rod bearing, the slight knock was heard and engine was cut off immediately, oil pan was removed and all bearings inspected, the number 4 rob bearing was the only bearing damaged and it was crushed, it left a few minor hot spots on the crank, tried refinishing with emery cloth and replaced the bearing but within a couple miles a slight knock started, the crank needs to be turned and recommend all bearings replaced. I am only selling because I have to many projects and want to focus on my 2004 BMW M3, plus I need to make room in the garage. This race car had no expense spared when built by Stage 6 Motorsports in Jacksonville FloridaThere is over $25K invested in parts in the engine and transmission not to mention the 100's of hours of labor that went into building this car. Pictures do this car no justice, I couldn't believe it when I first saw it. The artwork in the airbrushing is AMAZING, i tried to capture as much as I could in the photos but it is 10 times better in person. The car was tuned on C16 race gas but also has an 18ld pump gas tune. It is fully street legal minus emissions (but in most states it is considered an antique and is emission exempt). For more information and pics go here - - - - - - ->http://stage6motorsports.com/jimhucks/jh_specs.html
Selling on EBAY http://cgi.ebay.com/ebaymotors/ws/eB...m=221118994668
Extra Parts
2xMH slicks 8.5x24.5 on 2 extra 15 inch Enkei RP F1 (6 total rims and tires)
Steering wheel mounted remote Hi/Lo boost switch
Haltech E6K Stand Alone Engine Management with Sony Viao laptop with program loaded for tuning
MSD 3 Step launch control with 10 different RPM "pills"
Transmission Scatter shield
Dyno'd at 602whp @ 30psi
READ: While dyno tuning the boost spiked to 32+psi and crushed the number 4 rod bearing, the slight knock was heard and engine was cut off immediately, oil pan was removed and all bearings inspected, the number 4 rob bearing was the only bearing damaged and it was crushed, it left a few minor hot spots on the crank, tried refinishing with emery cloth and replaced the bearing but within a couple miles a slight knock started, the crank needs to be turned and recommend all bearings replaced. I am only selling because I have to many projects and want to focus on my 2004 BMW M3, plus I need to make room in the garage. This race car had no expense spared when built by Stage 6 Motorsports in Jacksonville FloridaThere is over $25K invested in parts in the engine and transmission not to mention the 100's of hours of labor that went into building this car. Pictures do this car no justice, I couldn't believe it when I first saw it. The artwork in the airbrushing is AMAZING, i tried to capture as much as I could in the photos but it is 10 times better in person. The car was tuned on C16 race gas but also has an 18ld pump gas tune. It is fully street legal minus emissions (but in most states it is considered an antique and is emission exempt). For more information and pics go here - - - - - - ->http://stage6motorsports.com/jimhucks/jh_specs.html
Selling on EBAY http://cgi.ebay.com/ebaymotors/ws/eB...m=221118994668
Thread
Thread Starter
Forum
Replies
Last Post
wade
Forced Induction
26
Oct 8, 2006 01:04 PM
