I am located in St. Louis. I am willing to ship everything but seats and engine blocks and transmissions. Everything else can be shipped, but buyer pays all shipping charges.


B20B... $250 OBO, I have the full longblock, including the p75 head






B20b Block -- $350 OBO
hot tanked and honed, will come with crank, and stock rods/pistons, oil pan, windage tray, oil pick-up tube, and a water crossover tube....





*Willing to sell with a set of forged h-beam rods for $475*


Eagle H-beam rods (2 sets) for LS/B20 -- $200 OBO /set



ITR Flywheel -- $100 OBO
I believe the weigh in at 16lbs... lighter than stock ls/gsr/b16, but heavier than aftermarket... retains intertia but improves acceleration. will need resurfaced before install.



Stock LS pistons and rods -- $80 OBO


Thick@$$ XS Power Aluminum Radiator -- sold


ARP 9mm Rod Bolts -- $50


Stock p28 ECU -- $100



P8R b20 head -- $100 OBO
only head with 84mm chamber bowls. flows better than the p75 LS head.



AEBS Intake Manifold for B16 -- $140
Ported on both ends, includes IACV and fuel rail if desired




Integra Type R 62mm throttle body -- $120 OBO
biggest stock throttle body you can get... the H22 throttle body is only 60mm at the butterfly, so it is not the same size as this one.



Ported and Polished B16 head -- sold



Rocket Motorsports dual Valve springs and Ti retainers -- $200 OBO




Hydro GSR transmission -- $350 OBO
I was told it is ready to go (bought from RPM Killa) just needs a bearing on the diff.

Cable GSR transmission -- sold




DA integra master cylinder $15 obo



PM6 ECU $25 OBO




B-series starter - $40 OBO



OBD1 and OBD0 resistor boxes - $15 OBO



B-series alternators - $50/each OBO




Axleback from a New Si... was going to use for a project, may not get around to it. - $120




B16B 4-2-1 Exhaust Manifold/heat shield. 2.5" collector. nice upgrade from stock while maintaining stock appearance. same deal, was going to use, may not get around to it - $120



GSR exhaust manifold/heatshield - $50 OBO








Set of Red striped del Sol seats, very minor tear in driverside bolster, and need a good cleaning - sold

Black SiR 3 bar steering wheel, nonSRS - $125


Comptech (Actually says Comptech, not etched "CT Engineering") Rear subframe brace and Swaybar for EG/DC... I believe the bar is a 22 or 23mm, but I can measure and verify - $250

(and without bar attached)

 

I will be going to Chicago this saturday, I can make a stop anywhere along the way there/back or meet up in Chicago if anyone is interested in something and can take advantage of that

 

ill take the del sol seats, can you get a pic of the tear?

 

bump

 

sick price on the del sol seats

 

What apps are the valvetrain for?

 

Vtec B-series



I'll go get that pic for you now, should be up in a few minutes.

 

pics of both seats:



seats are currently in my sol, I use them every day and they still feel great.. I forget there is a tear there to be honest

 

Also:
B20B... $300 OBO, I have the full longblock, including the p75 head (the first item listed in the original post)
^^Willing to take $200 for this motor if gone in the next week (I can meet anywhere along Hwy55 between st. louis and chicago on saturday). it is sitting in the middle of my work room and its in my way, so it needs to go!

 

what all would it need for a cplete swap?

 

everything but the block and head... intake/exhaust manifolds, alt., transmission, axles, mounts, wiring

 

would you be willing to meet

 

Where do you live? your Location says Illinois...
I am driving though Illinois to Chicago on saturday, I am open to meeting anywhere along the way if that works...

 

top

 

coming to wis? if so, i might take that b20 longblock off you ^_^

 

I am only going to Chicago for the day this weekend... you are welcome to come and meet me tho

 

meet me in gurnee mills, il and i'll pick it up off you for 200. is it in running condition or does it need a rebuild?

 

I have never run the motor, I bought it to rebuild and never got around to doing it.

 

gurnee mills is a little north for me... I'm going to be in Chicago only for the day to support a friend of mine who is competing in his first D1 event...but PM me and maybe we can work something out

 

im located in aurora, but i work during the day until 7....if you want to meet me at my work in the am when ur on ur way out i could swing that otherwise itd have to be after 7

 

friday bump

 

radiator, seats, cable tranny sold.