sup everyone i just swapped out my ls cluster with my new usdm itr cluster. before i installed it my old cluster was at 1/2 a tank, and now with the itr cluster in it is a little over full tank. does anyone know why this might be?

 

What year is your LS? You most likely just need to swap the green film over from your LS cluster.

 

i have a 95

 

Yes, just swap the green film from your LS cluster onto the ITR cluster, and all should be well.

 

i followed BlueIntegraBoy's writeup https://honda-tech.com/zerothread/1836281

 

anyone else have this problem

 

So are you using the LS green film, or the ITR?

 

make sure the screws in the back for the fuel guage is really tighten down..the same thing happen to me but with the cold/hot (temperture)gauge

 

Im using the itr film. as for you 3rdgenin i'll go and make sure the screws are on there tight. i'll let you guys know how it goes

 

Use the LS film.

 

so i just tightened up all the screws again and the gas guage still sits above full. im wondering if i should just fill it up and see if it goes down as the gas goes down. what do you guys think

 

anyone?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Padawan &raquo;</TD></TR><TR><TD CLASS="quote">Use the LS film. </TD></TR></TABLE>

 

what is the reasoning behind this? blueintegraboy said not to do it

 

I'm no electronics whiz, but I'd assume if you compared the two, there would be differences. If there are, then those differences could account for why your gas gauge is not working correctly.

*edit* I just read the whole thread, it doesn't say "not to do it" in terms of swapping out the green film. It said he was showing you how to swap the gauges out instead of doing the green film.

 

use the damn ls flim!!! gezzz i did the same thing, listen to padawan, use the ls flim!! damn man so ignorant...

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BOTAN01 &raquo;</TD></TR><TR><TD CLASS="quote">what is the reasoning behind this? blueintegraboy said not to do it</TD></TR></TABLE>

I never said to use the ITR film. My link shows you how to swap over the gauges, NOT to swap films.

Swapping film method doesn't really work well with 94-97 to 98-01 conversions since the ABS wire is in a totally different location.

You must use your LS film and housing with ITR gauges.

 

I followed BlueIntegraBoy's instructions exactly the way he explains it and all of my lights/gauges function correctly. All of the dummy plates need to be swapped around so that the check engine light, low fuel, etc light up in the proper area. You can't go wrong with hid DIY thread for swapping the gauges into the LS housing.

 

use the LS film!!!!!!

hahaha.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by gsrob &raquo;</TD></TR><TR><TD CLASS="quote">I followed BlueIntegraBoy's instructions exactly the way he explains it and all of my lights/gauges function correctly. All of the dummy plates need to be swapped around so that the check engine light, low fuel, etc light up in the proper area. You can't go wrong with hid DIY thread for swapping the gauges into the LS housing. </TD></TR></TABLE>

dude i'm sorry but this is pathetic

padawan told you like 5 times how it fix it, as well as othes, but you got a hard on for this blueballintegra guy....

for being dense

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by GRAF-FITI &raquo;</TD></TR><TR><TD CLASS="quote">

dude i'm sorry but this is pathetic

padawan told you like 5 times how it fix it, as well as othes, but you got a hard on for this blueballintegra guy....

for being dense</TD></TR></TABLE>

You are quoting the wrong person.

 

haha touche

OOPS clicked the wrong post to quote

still....i think you understand who i was referring to

 

dont know how to read or what? if youre not going to listen to our opinions, then why bother posting up a question?

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Padawan &raquo;</TD></TR><TR><TD CLASS="quote">What year is your LS? You most likely just need to swap the green film over from your LS cluster. </TD></TR></TABLE>

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Padawan &raquo;</TD></TR><TR><TD CLASS="quote">Use the LS film. </TD></TR></TABLE>

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Padawan &raquo;</TD></TR><TR><TD CLASS="quote">[/QUOTE]

[QUOTE=diLLy]use the LS film!!!!!!

hahaha.</TD></TR></TABLE>

 

blueballintegraguy. lmao!! you guys are crazy!! you gotta love that graf-fiti tho. but yeah why doesnt he just use the ls film?

 

can u swap 98 ls auto to a itr............?