i have been looking for a GARRETT intercooler core online but the few places that sell them offer them at retail price, anyone now a place that sells these cheaper?

the size im looking for:

GARRETT part number: 703522-6004

length 18.0
height 12.0
width 4.5

 

sometimes i can get pretty good deals on garrett intercoolers. give us a call at 301 290 0330 and talk to jeff. he should be able to help you out

 

 

BoostedJeff sent you a pm.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by ROTARY &raquo;</TD></TR><TR><TD CLASS="quote">BoostedJeff sent you a pm.</TD></TR></TABLE>

Replied, and spoke with you

 

What did you guys talk about?

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by tony1 &raquo;</TD></TR><TR><TD CLASS="quote">What did you guys talk about?</TD></TR></TABLE>

the birds and the bees

 

I don't get why people do that? I mean he is going to see the PM before he reads the thread.. I never understood the point of people sending a PM than posting that they did.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by tony1 &raquo;</TD></TR><TR><TD CLASS="quote">What did you guys talk about?</TD></TR></TABLE>

he gave me a good deal on a IC core.

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by danielm3 &raquo;</TD></TR><TR><TD CLASS="quote">I don't get why people do that? I mean he is going to see the PM before he reads the thread.. I never understood the point of people sending a PM than posting that they did.</TD></TR></TABLE>

most people check their Pm's right after entering a forum they don't keep checking their mailbox every 5 minutes, i wanted to ask him a few questions via instant messaging before he went offline so posting in my thread is a way to notify him in case he had already checked his mailbox before i sent my message.

danielm3 - when will your 3" aluminum u-bends be ready for purchase?

 

I was just playin'

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by tony1 &raquo;</TD></TR><TR><TD CLASS="quote">I was just playin' </TD></TR></TABLE>

Dammit tony, this is a message board, not a playground!

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by ROTARY &raquo;</TD></TR><TR><TD CLASS="quote">

he gave me a good deal on a IC core.

most people check their Pm's right after entering a forum they don't keep checking their mailbox every 5 minutes, i wanted to ask him a few questions via instant messaging before he went offline so posting in my thread is a way to notify him in case he had already checked his mailbox before i sent my message.

danielm3 - when will your 3" aluminum u-bends be ready for purchase? </TD></TR></TABLE>

I c but don't PM just pop up on this board with every refresh of the page?

As for the 3" Alum u bends, that would be almost impossible to do with a 16g wall. The outside would be way too thin and weak.. you would be able to poke a hole in it with your finger probably.. that is why I am guessing I have only seen up to 90 degrees.

 

i know.


danielm3 - i have that message pop-up feature on my rx-7 forum but i don't know how to enable it here on H-T.

i think that 16 gauge would be the thinnest part of the u-bend, i just measured a cut u-bend from my scrap box and the un-stretched section of the u-bend measured at .090" and the thinnest stretched section measured at .050"

 

A 16ga tube starts at .065, it's going to get thinner on the outer bend. Sounds like your bend started life as .090 wall tubing.

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by danielm3 &raquo;</TD></TR><TR><TD CLASS="quote">I don't get why people do that? I mean he is going to see the PM before he reads the thread.. I never understood the point of people sending a PM than posting that they did.</TD></TR></TABLE>

Actually I appreciate when people let me know, we have 2 computers here, and one of them just WILL NOT pop up PMs. We have turned off the pop up blocker, and tried everything

 

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BoostedJeff &raquo;</TD></TR><TR><TD CLASS="quote">

Actually I appreciate when people let me know, we have 2 computers here, and one of them just WILL NOT pop up PMs. We have turned off the pop up blocker, and tried everything</TD></TR></TABLE>

I get it now.. I didn't want to sound rude or anything, I was just really curious as to why people do that.

 

^ its cool

BoostedJeff - i got my H-T pop-up windows to work, try this

go to internet options &gt; click on (trusted sites) then click on (sites) and add https://honda-tech.com to the list then close that window &gt; click on (custom level) and disable pop-up blocker there.