FS: 2000 FBP ITR Need to sell!!!
Name:Bryan Latimer
Location:Williamsburg
Means of Contact
M, AIM, Cell- 757-817-0542
Description:2000 Acura Integra Type R
Miles:85,xxx miles: 15,000 on rebuilt engine
Price:$14,250 NEED TO SELL!!!( I HAVE PAPERWORK FOR ROUGHLY $5k)
Just picked up an 06' Canyon to replace the R because i need the truck for the snow/beach/ and my house in the mountains, snowboarding, also to haul my bike around. Just more practical for me to have than the R. Now I'm moving out and really really can't afford to have it anymore. In my opinion 14,250 is pretty much giving it away. I hate to see it go, i have had it for 2 years now and taken great care of it. I really would like to sell it on here, but if it doesn't sell soon im going to trade it to a used car place or auction . Worst case scenario i'd have to sell stuff off of it to make the payments, and i'd hate to see my hard work end up that way. PM me on here with any questions or if you need more pics of anything.
MODS:
-SRP 11.6:1 forged pistons and rings .20 overbore
-3 angle valve job, and mirror finished head. NO port and polish
-new exhaust valve guides
-Machine work done by Dunkums Machine shop Block assembled by Custom Car Care
- OEM head gasket
-All new OEM Honda bearings/gaskets/seals
-OEM Honda water pump, oil pump, timing belt, a/c belt, p/s belt
-exedy stage 1 clutch installed about 10k miles ago
-Energy Motor mount insert in rear
-Energy shifter bushings
-re-painted engine bay when the motor was out.
-Hondata intake manifold gasket
-hondata s200 tuned by CCC 173hp 122 tq and i get 29-33mpg
-obd2-obd1 conversion harness
-New Dunlop tires 205/55/15 maybe 500 miles on them
-Brembo cross drilled and slotted rotors w/ oem pads all around
-H&R ITR specific springs Ride very nice they are on stock struts, im sure koni's would be a very big improvement
-SPC forged upper control arms (camber kits) With alignment by CCC
-Spacer kit for the back camber uninstalled
-Test pipe to Apexi N1 exhaust
-Like new floormats and trunk mat
-very clean interior
-35% tint in the back (had to take the front off for a ticket)
-Comptech Icebox intake
-OEM optional Kit, Driver side sideskirt doesnt fit the best for some reason -normal paint chips on front bumper, and scratches on the passenger side fender from previous owner, scuff mark on back bumper. small stuff really.
-A/C blows cold
-HID headlights(6k i think) and oem fogs
-jdm steering wheel (horn works)









Location:Williamsburg
Means of Contact
M, AIM, Cell- 757-817-0542Description:2000 Acura Integra Type R
Miles:85,xxx miles: 15,000 on rebuilt engine
Price:$14,250 NEED TO SELL!!!( I HAVE PAPERWORK FOR ROUGHLY $5k)
Just picked up an 06' Canyon to replace the R because i need the truck for the snow/beach/ and my house in the mountains, snowboarding, also to haul my bike around. Just more practical for me to have than the R. Now I'm moving out and really really can't afford to have it anymore. In my opinion 14,250 is pretty much giving it away. I hate to see it go, i have had it for 2 years now and taken great care of it. I really would like to sell it on here, but if it doesn't sell soon im going to trade it to a used car place or auction . Worst case scenario i'd have to sell stuff off of it to make the payments, and i'd hate to see my hard work end up that way. PM me on here with any questions or if you need more pics of anything.
MODS:
-SRP 11.6:1 forged pistons and rings .20 overbore
-3 angle valve job, and mirror finished head. NO port and polish
-new exhaust valve guides
-Machine work done by Dunkums Machine shop Block assembled by Custom Car Care
- OEM head gasket
-All new OEM Honda bearings/gaskets/seals
-OEM Honda water pump, oil pump, timing belt, a/c belt, p/s belt
-exedy stage 1 clutch installed about 10k miles ago
-Energy Motor mount insert in rear
-Energy shifter bushings
-re-painted engine bay when the motor was out.
-Hondata intake manifold gasket
-hondata s200 tuned by CCC 173hp 122 tq and i get 29-33mpg
-obd2-obd1 conversion harness
-New Dunlop tires 205/55/15 maybe 500 miles on them
-Brembo cross drilled and slotted rotors w/ oem pads all around
-H&R ITR specific springs Ride very nice they are on stock struts, im sure koni's would be a very big improvement
-SPC forged upper control arms (camber kits) With alignment by CCC
-Spacer kit for the back camber uninstalled
-Test pipe to Apexi N1 exhaust
-Like new floormats and trunk mat
-very clean interior
-35% tint in the back (had to take the front off for a ticket)
-Comptech Icebox intake
-OEM optional Kit, Driver side sideskirt doesnt fit the best for some reason -normal paint chips on front bumper, and scratches on the passenger side fender from previous owner, scuff mark on back bumper. small stuff really.
-A/C blows cold
-HID headlights(6k i think) and oem fogs
-jdm steering wheel (horn works)









Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post





