obd-1 b18c
Thread Starter
Joined: Apr 2002
Posts: 3,523
Likes: 0
From: W.A
obd-1 b18c
B18c1:
golden eagle sleeves
wiseco 9.5:1 compression pistons
Eagle rods.
The bottom end was assembled by a reputable shop using acl bearings.
Comes with new water pump, timing belt, stock head gasket, and golden eagle head studs.
Also comes with act extreem pressure plate and 6puck disk.
$3,800 obo
The engine has -0- miles on it, none, never been driven since the build....not even once.......
b16a hydrolic tranny $550 obo.
The engine is assembled right now and would like to sell it as a short or long block, but if someone is interested in the block i'll part the two. Prices are not firm and can be negotiated. I don't want to part out the little stuff unless the big stuff sells first .
I'm going to post this anyways, but i'm 95% sure it's sold.
garrett t3t4 .57 trim .63 A/R
Drag manifold
tial 35mm wg w/dump tube..
21x9x3" fmic w/piping.
megan racing bov
gm 3bar map
756cc injectors
holley 255lph intank pump
resistor pack
boost gauge and pod.
Hondata s100
If the sale falls through $2,000 obo B-sereis of course.
93 civic cx hatch.
comes with sparco speeds, one harness (rci, brand new never installed) the rear seat, plastics, stock passenger seat..dash etc..
rolling on 14" stock wheels (look like del sol wheels)
the car needs paint and a few trim pieces (driver side window molding (bottom of the window where it meets the door $25 part i just havent picked it up yet)...the body is good no dents. Does have a salvaged title.
Price is negotiable $1000
If your interested let me know, like I said all prices are negotiable. Low ball me and you'll be ignored, if you don't have a clue how much some of the parts cost then ask me.
"Thanks for looking and Please bump this if you read it" Thanks
___________
Modified by b16ahybrid at 9:24 PM 3/28/2006
golden eagle sleeves
wiseco 9.5:1 compression pistons
Eagle rods.
The bottom end was assembled by a reputable shop using acl bearings.
Comes with new water pump, timing belt, stock head gasket, and golden eagle head studs.
Also comes with act extreem pressure plate and 6puck disk.
$3,800 obo
The engine has -0- miles on it, none, never been driven since the build....not even once.......
b16a hydrolic tranny $550 obo.
The engine is assembled right now and would like to sell it as a short or long block, but if someone is interested in the block i'll part the two. Prices are not firm and can be negotiated. I don't want to part out the little stuff unless the big stuff sells first .
I'm going to post this anyways, but i'm 95% sure it's sold.
garrett t3t4 .57 trim .63 A/R
Drag manifold
tial 35mm wg w/dump tube..
21x9x3" fmic w/piping.
megan racing bov
gm 3bar map
756cc injectors
holley 255lph intank pump
resistor pack
boost gauge and pod.
Hondata s100
If the sale falls through $2,000 obo B-sereis of course.
93 civic cx hatch.
comes with sparco speeds, one harness (rci, brand new never installed) the rear seat, plastics, stock passenger seat..dash etc..
rolling on 14" stock wheels (look like del sol wheels)
the car needs paint and a few trim pieces (driver side window molding (bottom of the window where it meets the door $25 part i just havent picked it up yet)...the body is good no dents. Does have a salvaged title.
Price is negotiable $1000
If your interested let me know, like I said all prices are negotiable. Low ball me and you'll be ignored, if you don't have a clue how much some of the parts cost then ask me.
"Thanks for looking and Please bump this if you read it" Thanks
___________
Modified by b16ahybrid at 9:24 PM 3/28/2006
Thread Starter
Joined: Apr 2002
Posts: 3,523
Likes: 0
From: W.A
Re: obd-1 b18c (b16ahybrid)
Trending Topics
Thread Starter
Joined: Apr 2002
Posts: 3,523
Likes: 0
From: W.A
Re: obd-1 b18c (turbob18si)
http://i78.photobucket.com/alb...t.jpg
http://i78.photobucket.com/alb...e.jpg
http://i78.photobucket.com/alb...r.jpg
Sale of the car is pending, I will know for sure this weekend.
If the car does sell this weekend I'll have a pair of sparco speeds w/rails up for sale(from the car)
The new price for the complete block including 8.5lb flywheel and ACT Extreem PP w/6 puck disk is $2,350....Clutch and flywheel are both brand new also....
All you'll need is a head and tranny and your set.
http://i78.photobucket.com/alb...e.jpg
http://i78.photobucket.com/alb...r.jpg
Sale of the car is pending, I will know for sure this weekend.
If the car does sell this weekend I'll have a pair of sparco speeds w/rails up for sale(from the car)
The new price for the complete block including 8.5lb flywheel and ACT Extreem PP w/6 puck disk is $2,350....Clutch and flywheel are both brand new also....
All you'll need is a head and tranny and your set.
Thread
Thread Starter
Forum
Replies
Last Post
BoostedEgHatchFl
Classifieds: Forced Induction
5
Sep 4, 2012 04:43 PM
oneI
Classifieds: Forced Induction
13
Jun 22, 2006 11:15 AM