FOR SALE: Built LS/VTEC with turbo
Thread Starter
Joined: Jun 2005
Posts: 276
Likes: 0
From: nor cal, ca, usa
FOR SALE: Built LS/VTEC with turbo
B16A Head, KG Engineering Stage 3 1.8 LS Block, LS cable tranny with welded diff and turbo
$2200 FIRM
Parts are located in Hayward, Ca. I'm moving so I need to sell fast.
Contact me if interested: 5105087720
PHOTOS:
http://pg.photos.yahoo.com/ph/...HmikY
ENGINE
- Civic Type-R intake cam
- Integra Type-R exhuast cam
- STR cam gears and fuel Rail
- Type-R Intake manifold
- ITR Throttle Body
- ITR valvetrain
- ARP head studs
- port and polished head
- Crower rods
- Arias pistons 9.5:1
- RC 750cc injectors
- Full metal jacket iron ductile sleeves
- Custom Clutch Masters stage 5 clutch
- Modified oil pump
- Micro Polished Crank
*No distributor or ECU/Harness
TURBO
- Custom Fastrax TO3/TO4 Hybrid turbo (may need to be rebuilt)
- Turbo Manifold
- Greddy Manual Boost Controller
- Turbo Piping
*I've also got a couple extra axles I"ll throw in
KG Engineering originally did the work on the block and I had LDL Speedshop clean it up for me. (Shop has relocated to Las Vegas). I have papers for the block.
I've never taken this motor to its full potential. Ran it at the track a few times then decided to change setup and I never finished. It's been sitting in my garage. It has potential to easily do 10's. The motor is in Hayward, Ca. Please contact me if you'd like to take a look at it or for questions.
Sorry I will not part out. Pick Up Only
Modified by ladyjetspeed at 1:01 PM 8/29/2005
$2200 FIRM
Parts are located in Hayward, Ca. I'm moving so I need to sell fast.
Contact me if interested: 5105087720
PHOTOS:
http://pg.photos.yahoo.com/ph/...HmikY
ENGINE
- Civic Type-R intake cam
- Integra Type-R exhuast cam
- STR cam gears and fuel Rail
- Type-R Intake manifold
- ITR Throttle Body
- ITR valvetrain
- ARP head studs
- port and polished head
- Crower rods
- Arias pistons 9.5:1
- RC 750cc injectors
- Full metal jacket iron ductile sleeves
- Custom Clutch Masters stage 5 clutch
- Modified oil pump
- Micro Polished Crank
*No distributor or ECU/Harness
TURBO
- Custom Fastrax TO3/TO4 Hybrid turbo (may need to be rebuilt)
- Turbo Manifold
- Greddy Manual Boost Controller
- Turbo Piping
*I've also got a couple extra axles I"ll throw in
KG Engineering originally did the work on the block and I had LDL Speedshop clean it up for me. (Shop has relocated to Las Vegas). I have papers for the block.
I've never taken this motor to its full potential. Ran it at the track a few times then decided to change setup and I never finished. It's been sitting in my garage. It has potential to easily do 10's. The motor is in Hayward, Ca. Please contact me if you'd like to take a look at it or for questions.
Sorry I will not part out. Pick Up Only
Modified by ladyjetspeed at 1:01 PM 8/29/2005
Trending Topics
Thread Starter
Joined: Jun 2005
Posts: 276
Likes: 0
From: nor cal, ca, usa
Re: FOR SALE: Built LS/VTEC with turbo (ladyjetspeed)
I also have:
JE PISTONS (9.5:1) & CROWER RODS - PR3 B16A - $250 OBO
BIG GREDDY Intercooler - core approx. 23"x11" (Type 24?) - $250 OBO
GROUND CONTROL drag coilovers w/ rated Eibach Springs (700.250.650lbs. front/600.250.1000lbs. rear) - 88-91 Civic - $125 OBO
Slightly used Red anodized STR Tow Hooks - There is a scrap on the bottom of the rear hook that you wont be able to see once installed on the car but other than that, its in good condition - $45 OBO
I'd like to sell these items ASAP so if there are no bids on any of these items...make me a reasonable offer. mjgines@hotmail.com thanks
I WILL SHIP but buy pays for shipping.
JE PISTONS (9.5:1) & CROWER RODS - PR3 B16A - $250 OBO
BIG GREDDY Intercooler - core approx. 23"x11" (Type 24?) - $250 OBO
GROUND CONTROL drag coilovers w/ rated Eibach Springs (700.250.650lbs. front/600.250.1000lbs. rear) - 88-91 Civic - $125 OBO
Slightly used Red anodized STR Tow Hooks - There is a scrap on the bottom of the rear hook that you wont be able to see once installed on the car but other than that, its in good condition - $45 OBO
I'd like to sell these items ASAP so if there are no bids on any of these items...make me a reasonable offer. mjgines@hotmail.com thanks
I WILL SHIP but buy pays for shipping.
Thread Starter
Joined: Jun 2005
Posts: 276
Likes: 0
From: nor cal, ca, usa
Re: FOR SALE: Built LS/VTEC with turbo (ladyjetspeed)
PHOTOS: http://pg.photos.yahoo.com/ph/...AmikY
I've got a few items listed on EBAY under username PNAYRCR:
B16A PR3 rods and pistons - $100 OBO
Newly Chromed Caliper Hats from 1995 Honda Civic - SOLD
JAZ 1 Gallon Fuel Cell with blue anodized fittings - SOLD
TURBONETICS Delta Mark II Wastegate - SOLD
BIG GREDDY Intercooler - core approx. 23"x11" (Type 24?) - $250 OBO
GROUND CONTROL drag coilovers w/ rated Eibach Springs (700.250.650lbs. front/600.250.1000lbs. rear) - 88-91 Civic - $125 OBO
Used SIMPSON 5pt. Harness with cam lock - Red - SOLD
Slightly used Red anodized STR Tow Hooks - There is a scrap on the bottom of the rear hook that you wont be able to see once installed on the car but other than that, its in good condition - $45 OBO
I'd like to sell these items ASAP so if there are no bids on any of these items...make me a reasonable offer. mjgines@hotmail.com thanks
I WILL SHIP but buy pays for shipping.
Modified by ladyjetspeed at 6:22 PM 9/1/2005
I've got a few items listed on EBAY under username PNAYRCR:
B16A PR3 rods and pistons - $100 OBO
Newly Chromed Caliper Hats from 1995 Honda Civic - SOLD
JAZ 1 Gallon Fuel Cell with blue anodized fittings - SOLD
TURBONETICS Delta Mark II Wastegate - SOLD
BIG GREDDY Intercooler - core approx. 23"x11" (Type 24?) - $250 OBO
GROUND CONTROL drag coilovers w/ rated Eibach Springs (700.250.650lbs. front/600.250.1000lbs. rear) - 88-91 Civic - $125 OBO
Used SIMPSON 5pt. Harness with cam lock - Red - SOLD
Slightly used Red anodized STR Tow Hooks - There is a scrap on the bottom of the rear hook that you wont be able to see once installed on the car but other than that, its in good condition - $45 OBO
I'd like to sell these items ASAP so if there are no bids on any of these items...make me a reasonable offer. mjgines@hotmail.com thanks
I WILL SHIP but buy pays for shipping.
Modified by ladyjetspeed at 6:22 PM 9/1/2005
Thread Starter
Joined: Jun 2005
Posts: 276
Likes: 0
From: nor cal, ca, usa
Re: FOR SALE: Built LS/VTEC with turbo (ladyjetspeed)
Brand New Holley Annihilator Race Cell Part# 880-105
- The cranking power of conventional a battery with the flexibility of a deep-cycle battery
- CCA: 470 (880-105)
- 880-105’s side-post mounting style fits easily in small spaces
- CNC-machined hold-down bracket is available under part number 880-103
- Dry cell design allows installation on its sides without fear of spillage
- Battery can be deep cycled hundreds of times
- When fully charged, battery can be stored for up to 2 years!
- High vibration resistance is perfect for use in harsh racing environments
- The 880-105 is 12% better than the 880-100!
- Weighs just 24 lbs.(880-105)
Brand New Holley battery hold down. Part# 880-103
A premium quality, high tech battery like the HOLLEY demands an equally capable battery hold-down fixture to keep everything in place. The HOLLEY Battery Hold-Down is crafted from 6061-T6 aircraft-quality aluminum and designed to look good while doing a great job.
http://www.holley.com/products.asp?product=880-105
http://www.holley.com/products.asp?product=880-103
Brand new both will cost you over $250. I want $160 obo
- The cranking power of conventional a battery with the flexibility of a deep-cycle battery
- CCA: 470 (880-105)
- 880-105’s side-post mounting style fits easily in small spaces
- CNC-machined hold-down bracket is available under part number 880-103
- Dry cell design allows installation on its sides without fear of spillage
- Battery can be deep cycled hundreds of times
- When fully charged, battery can be stored for up to 2 years!
- High vibration resistance is perfect for use in harsh racing environments
- The 880-105 is 12% better than the 880-100!
- Weighs just 24 lbs.(880-105)
Brand New Holley battery hold down. Part# 880-103
A premium quality, high tech battery like the HOLLEY demands an equally capable battery hold-down fixture to keep everything in place. The HOLLEY Battery Hold-Down is crafted from 6061-T6 aircraft-quality aluminum and designed to look good while doing a great job.
http://www.holley.com/products.asp?product=880-105
http://www.holley.com/products.asp?product=880-103
Brand new both will cost you over $250. I want $160 obo
