f1 vtec

t3/t4e turbo will be going on my car soon running approx 15psi, if u have a t3/t4e please post up what power your car is throwing out at how much boost. it will give me a fair idea on what to expect with mine, would be gratefull if you could post setup info or any dynos.
wanna also get a fair idea on whats the max i can push with this turbo
thanks

crx2fast

what engine you plaining on running/setup other than the t3/t4

f1 vtec

see sig, hoping to get around 350hp

delsolio

273hp and 186tq @7psi

f1 vtec

Boostfed

Drag 3 kit which comes with a T3/T04B made 370whp 21psi, befor eon stock motor made 243whp 276ft-lb torque, 18 psi before Hondata made 320whp 256 ft-lb. FOund out later was supposed to be a T3/T04 with Super V trim compressor wheel, it was actually a T04B S trim SMALLEST wheel made, then Stage 1 turbine instead of what was supposed to be a Stage 3 wheel. Still made good power for what it was.

Trip

You were riding right at the surge limit on that thing if that's the case. Like 60% efficiency if you were lucky. Great #'s I'd say.

f1 vtec

nice numbers

turbosi03

I have a t3/to4e from the drag 3 kit... made 347whp @13.7psi with a blown HG... but the b16 was bored/stroked to a 2.0L, and I don't know if and how much power was lost because of a **** load of water went through the motor...

RacerXI

See sig for numbers at 10.5psi.
SFP manifold
2.5 - 3" past the compressor to 3" catback.
9.27:1CR B16

utahbmx

check out my sig ------>

f1 vtec

^^^you guys are running some good numbers on low boost^^
makes me seem my target is more and more achievable

----Lets have some more numbers setups/dynos---
thanks

SiR Kid

9:1 b16a, basic mods, 265HP @ 14 psi from a Precision SC34, 60 a/r 57 trim turbo, 63 stage 3 exhaust side.

Went 13.3@114 on 195/50/15 Potenza S-03's and blown shocks.

f1 vtec

keep the numbers rollin in any dyno sheets etc

PM-Performance

with my t3/04e i did 350whp at 10psi . i never really upped the boost on that turbo, but i coulda made 500 on that thing. it was a bad little turbo .

TurboJesse

Stock b16a block, inline pro headgasket, cam gears, arp head studs, SSAC manifold, 60 trim t3/t4oe .63a/r, 450 DSM injectors, Hondata s100 w/boost, , Tial wastegate and Sheepdog BOV.

f1 vtec

^^^nice numbers what boost you running^^^

TurboJesse

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by f1 vtec &raquo;</TD></TR><TR><TD CLASS="quote">^^^nice numbers what boost you running^^^</TD></TR></TABLE>

13-14psi

The car made over 250whp off the .45bar spring. The final tune @ 307whp is very conservative and hardly any timing in the motor.

f1 vtec

bump it up for more posts!!!

kleefton

2000 civic sI
9:1 cp pistons, eagle rods
81.5mm bore
Revhard kit with a
50 TRIM T3/T04E
.60/.63 A/R, Stage 5 wheel (or a precision sc50)
780cc injectors
hondata s200b
3" catless exhaust after 2.5" dp

14.7psi = 298whp/ 212 lbs/ft
a/f = 11.5 accross the board

g2turbo

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Boostfed &raquo;</TD></TR><TR><TD CLASS="quote">Drag 3 kit which comes with a T3/T04B made 370whp 21psi, befor eon stock motor made 243whp 276ft-lb torque, 18 psi before Hondata made 320whp 256 ft-lb. FOund out later was supposed to be a T3/T04 with Super V trim compressor wheel, it was actually a T04B S trim SMALLEST wheel made, then Stage 1 turbine instead of what was supposed to be a Stage 3 wheel. Still made good power for what it was. </TD></TR></TABLE>


My car made 238whp on 13lbs. with the same kit. It was 8.8:1 b16.
t3/to4b with .48 exhaust

needless to say im gonna **** my pants going from that... to a 9.8:1 gsr motor and gt35e/t4

slowhitecrx

b16 stock bottom t3/t4 running only 4 psi due to ignition and no EMS yet laid down 261 whp and 160 ft lbs...

See Are X

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by slowhitecrx &raquo;</TD></TR><TR><TD CLASS="quote">b16 stock bottom t3/t4 running only 4 psi due to ignition and no EMS yet laid down 261 whp and 160 ft lbs... </TD></TR></TABLE>

wow, on only 4psi? im hoping mine makes that much at 7psi

ham

im only gonna run .3 bar on my stock b16 w/ t3/t4. good numbers with that. i plan on going to .5 after everything is good.

f1 vtec

average seems to be around 250whp@7psi
lets have some big numbers too,what boost can these turbos see what hp can they produce