Can someone fab me a b-series "low profile" PS bracket?
#2
Honda-Tech Member
Join Date: Feb 2006
Location: East Bay, CA, USA
Posts: 1,524
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
shave that bolt down or just pull it out. the bracket will stay put with one bolt holding it in.
#6
Honda-Tech Member
Thread Starter
Join Date: Sep 2003
Posts: 349
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
Thanks for the suggestions, i was thinking of getting a M14 x 6mm spacer, then make a 2 pieces CNC aluminum to replace the bracket hehe... That would shave like 1lb and look prettier.
But I think going countersink + this bolt: http://www.onlinefasteners.com.au/on...ners/node/1079
Should get the job done and save some money haha...
But I think going countersink + this bolt: http://www.onlinefasteners.com.au/on...ners/node/1079
Should get the job done and save some money haha...
#7
Honda-Tech Member
Thread Starter
Join Date: Sep 2003
Posts: 349
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
@LKSi where did you get your M14 countersunk bolt? The site i found don't ship internationally. And I've been trying to find other place, none of them sells it (not on ebay either)
Trending Topics
#8
Honda-Tech Member
Join Date: Jan 2006
Location: Cleveland, TN, United States
Posts: 252
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
i just cut mine in half and just used the one bolt. make sure its level before you tighten it. works great.
#9
Honda-Tech Member
Re: Can someone fab me a b-series "low profile" PS bracket?
That sounds so shitty. LST.
Mill the face down and use a shorter bolt with a countersunk head. That you can do at home if you are on a super budget with a grinder and you put the part in a drill press to countersink.
Mill the face down and use a shorter bolt with a countersunk head. That you can do at home if you are on a super budget with a grinder and you put the part in a drill press to countersink.
#10
Honda-Tech Member
Thread Starter
Join Date: Sep 2003
Posts: 349
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
Anyone know where to get a M14 countersunk bolt? RenoDepot/HomeDepot/Rona here don't sell such a big bolt here (they have M14 but is not countersunk)
Basically need M14 x 45mm
Basically need M14 x 45mm
#11
Honda-Tech Member
Join Date: Jul 2003
Location: Houston, USA
Posts: 3,831
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
#12
Honda-Tech Member
Join Date: Jan 2005
Location: Lower Right Hand Corner, PA
Posts: 5,643
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
You don't need to counter sink that, just take a grinder and notch the "bulge" flat with the flange. Will fit just fine, might even be able to use the same bolt.
#13
Honda-Tech Member
Join Date: Jul 2005
Location: The Empire State
Posts: 813
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
Those bolts are going to be 10x1.25mm dude. Just because its a 14mm head doesn't mean anything.
#14
Honda-Tech Member
Join Date: Sep 2002
Location: Vila Velha, Brasil
Posts: 1,666
Likes: 0
Received 0 Likes
on
0 Posts
Re: Can someone fab me a b-series "low profile" PS bracket?
I just cut my bracket and it looks OEM. It wont look shitty. I'll take a pic of it.
Adriano
Adriano
Thread
Thread Starter
Forum
Replies
Last Post
the soL that could
Honda Civic / Del Sol (1992 - 2000)
9
09-12-2011 06:19 AM
117
Road Racing / Autocross & Time Attack
16
04-02-2009 10:18 PM
albert butterbikini
Acura Integra Type-R
4
06-30-2001 02:54 PM