parting out car & turbo motor
#1
Honda-Tech Member
Thread Starter
Join Date: May 2006
Location: 714
Posts: 821
Likes: 0
Received 0 Likes
on
0 Posts
parting out car & turbo motor
time has come to sell everything and start over with something bigger. new car & new motor...
car is sold already just need to sell the aftermarket parts and put stocks back on.
first up is the motor.. pic upon request!!
BUMP IF VIEWED PLZ!!!
Everything on motor has bout 1 dyno session and 1 event
Garret gt3067r turbo $750
b18c sleeved to 81mm needs line bore $ 900
JE pistons 81mm skirt little scratched but runnable $250
Eagle Ls rods $200
x2 Knifed Edged LS crank $ 250 each
PortFlow GSR Build head $ 1000
Victor X manifold Heat treated black $320
Rc 1600cc $350
Bdl Fuel Rail $80
BDL Regulator $120
BDL Throttle body 72mm $ 200
CTR cams bout 40k on them $300
gsr tranny stock gears $450
b16 tranny; 1-4 gsr 5 ls, quaife lsd $1200
i think that is all the motor **** i have i will add once i look to see what else i have!!!
now supension parts
Tein flex; revalved 2 months ago for high springs rate $ 1000
Front skunk2 camber kit $80 (SOLD)
rear omni camber kit $60 (SOLD)
Rear skunk2 lcr gold $180 (SOLD)
Rear ST sway bar tie bar combo $250 (SOLD)
Skunk2 extended studs $3.50 each have 16 (sold 8) 8 left
Wilwood 6pistons bbk w/ race pads $1100 need 16in wheels to clear.
Rota slipstreems 16x8 +38 bnib $500
Rota slepstreems 16x8 +38 w/ proxy r888 1 event on them. $1000 tires cost bout 800...
Sparco Sprint seat with eg/dc rail and slider $ 300 (SOLD)
Sparco sprint 5 seat $220 (SOLD)
Sparco 6 point cam harness 3inch $250 nhra/nasa/scca approved
Sparco Steering wheel $150
nrg quick release $ 80
nrg hub $ 80
Cusco 6 point cage w/ add harness bar for DELSOL $600
I think thats it i gotta put car up to see what else. lmk if any1 interested everything still on car. so u can come check it out.
THANKS AGAGIN
BUMP IF VIEWED!!!
car is sold already just need to sell the aftermarket parts and put stocks back on.
first up is the motor.. pic upon request!!
BUMP IF VIEWED PLZ!!!
Everything on motor has bout 1 dyno session and 1 event
Garret gt3067r turbo $750
b18c sleeved to 81mm needs line bore $ 900
JE pistons 81mm skirt little scratched but runnable $250
Eagle Ls rods $200
x2 Knifed Edged LS crank $ 250 each
PortFlow GSR Build head $ 1000
Victor X manifold Heat treated black $320
Rc 1600cc $350
Bdl Fuel Rail $80
BDL Regulator $120
BDL Throttle body 72mm $ 200
CTR cams bout 40k on them $300
gsr tranny stock gears $450
b16 tranny; 1-4 gsr 5 ls, quaife lsd $1200
i think that is all the motor **** i have i will add once i look to see what else i have!!!
now supension parts
Tein flex; revalved 2 months ago for high springs rate $ 1000
Front skunk2 camber kit $80 (SOLD)
rear omni camber kit $60 (SOLD)
Rear skunk2 lcr gold $180 (SOLD)
Rear ST sway bar tie bar combo $250 (SOLD)
Skunk2 extended studs $3.50 each have 16 (sold 8) 8 left
Wilwood 6pistons bbk w/ race pads $1100 need 16in wheels to clear.
Rota slipstreems 16x8 +38 bnib $500
Rota slepstreems 16x8 +38 w/ proxy r888 1 event on them. $1000 tires cost bout 800...
Sparco Sprint seat with eg/dc rail and slider $ 300 (SOLD)
Sparco sprint 5 seat $220 (SOLD)
Sparco 6 point cam harness 3inch $250 nhra/nasa/scca approved
Sparco Steering wheel $150
nrg quick release $ 80
nrg hub $ 80
Cusco 6 point cage w/ add harness bar for DELSOL $600
I think thats it i gotta put car up to see what else. lmk if any1 interested everything still on car. so u can come check it out.
THANKS AGAGIN
BUMP IF VIEWED!!!
Last edited by devsol; 06-23-2009 at 01:13 PM.