My B20 Build....
#1
Honda-Tech Member
Thread Starter
Join Date: Jun 2009
Location: San Antonio, Tx
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
My B20 Build....
Well it's been a while since I have posted, therefore I decided to make a build thread for my next motor setup which will be a fully Built B20 Vtec all motor. As the days go by I will do my best to post as many pics as I can and give full detail of what my build will consume of. For now it is removing the B16B engine which is a blast to drive, but I wanted more torque! LOL! I started off by removing the engine today this morning and I decided that my next investment will be an engine hoist. It was difficult for me to pull the engine out from underneath with the shitty jack I had. The engine bay will be repainted as well,if anyone is interested i will be selling the car shortly after the motor is built and tuned, I have realized that I have lost interest in Honda's and now it's time for me to move on in life. Please don't ask how much, i will decide when I am done finishing this build. But for now here are a couple pics enjoy..
Cleaned the engine bay and the tranny will try and update as much as i can....
Cleaned the engine bay and the tranny will try and update as much as i can....
#6
Honda-Tech Member
Thread Starter
Join Date: Jun 2009
Location: San Antonio, Tx
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Re: My B20 Build....
K it has been a while since I posted because I had lost interest in my build but its on once again.... I painted My block,tranny and other things. I actually liked the outcome, they came out good. I was scared that they may of came out shiny I didn't want that. The paint I picked turned out to be very good enjoy...
b20b block Golden eagle Sleeved 86mm, Golden Eagle Head Gasket
Golden Eagle Block Guard (Yes I am running a block guard on a sleeved block)
Micro polished Crank
ARP Head studs
AZ Race& Machine Girdle
JE Pistons 11:1
Scat Rods
New Oil pan and gasket
Fully port and Polished P72 head and 3 angle valve job
All Jun Valve train Including Jun type 3 cams Golden Eagle Cam Gears
Greddy Timing belt
Skunk 2 Intake Manifold, Skunk 2 70mm Throttle Body,Golden Eagle Fuel rail
New Type r Oil and Water pump,Walbro 255 fuel pump
probably forgetting some things but I will update......
Still need injectors,clutch and a header... I have rc310's but some say they are too small others say it will be fine. Any recommendations are appreciated...
b20b block Golden eagle Sleeved 86mm, Golden Eagle Head Gasket
Golden Eagle Block Guard (Yes I am running a block guard on a sleeved block)
Micro polished Crank
ARP Head studs
AZ Race& Machine Girdle
JE Pistons 11:1
Scat Rods
New Oil pan and gasket
Fully port and Polished P72 head and 3 angle valve job
All Jun Valve train Including Jun type 3 cams Golden Eagle Cam Gears
Greddy Timing belt
Skunk 2 Intake Manifold, Skunk 2 70mm Throttle Body,Golden Eagle Fuel rail
New Type r Oil and Water pump,Walbro 255 fuel pump
probably forgetting some things but I will update......
Still need injectors,clutch and a header... I have rc310's but some say they are too small others say it will be fine. Any recommendations are appreciated...
Trending Topics
#10
Honda-Tech Member
Thread Starter
Join Date: Jun 2009
Location: San Antonio, Tx
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Re: My B20 Build....
I went through 4 different cans and finally picked this one-
Rust-Oleum 248904 Automotive 12-Ounce High Heat 2000 Degree Spray Paint, Flat Aluminum.Just make sure you prep and do many light coats instead of big coats and let it dry.
Just Google that bro.
#12
Honda-Tech Member
Thread Starter
Join Date: Jun 2009
Location: San Antonio, Tx
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Re: My B20 Build....
Sorry it's been a while again since I posted, but just got around to painting the engine bay this past Thursday and receiving my manifold back from powder coating. LMK what you guys think thanks....
#16
Honda-Tech Member
Thread Starter
Join Date: Jun 2009
Location: San Antonio, Tx
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Re: My B20 Build....
So my buddy finally got some time to start assembling the motor together, here are some picks of what was accomplished last night. I will do my best to upload as many pictures of the progress.
Any comments are welcome...
Any comments are welcome...
#17
Honda-Tech Member
Thread Starter
Join Date: Jun 2009
Location: San Antonio, Tx
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Re: My B20 Build....
New Honda hardware everything was cleaned up before assembling and properly torqued down, at this point I'm getting excited and thanks to my buddy aka (CBR racing) for making this possible.
Last edited by b20_EM1; 08-19-2011 at 06:27 PM.