Honda-Tech - Honda Forum Discussion

Notices
Search: Posts Made By: Sk8ermane
Showing results 1 to 17 of 17
Search took 0.75 seconds.
Forum: Hybrid / Engine Swaps
09-05-2008, 07:26 PM
Replies: 4
Views: 2,048
Posted By Sk8ermane

Re: Got the iabs working with the p28 (Katman)

It's way more of an improvement. I had the iabs open the whole time I got my swap, and it bogged really bad. Now it not only feels like a flat power curve, but vtech comes on way smoother and linear...
Forum: Hybrid / Engine Swaps
09-03-2008, 08:01 PM
Replies: 4
Views: 2,048
Posted By Sk8ermane

Got the iabs working with the p28

Just letting you guys know that the iab's on a stock gsr intake manifold can easily be activated through a relay that is powered by the vtech solenoid. Obviously, the only downside is that the iab's...
Forum: Hybrid / Engine Swaps
02-25-2008, 02:10 PM
Replies: 1
Views: 1,279
Posted By Sk8ermane

Re: Bad idle surge, running really rich, code 14 on an lsvtec (Sk8ermane)

well, in case anyone has the same problem, I am pretty sure I know what is wrong, its the fast idle air valve. It was really loose, but I didnt tighten it up I think, so I will take the tb off...
Forum: Hybrid / Engine Swaps
02-24-2008, 04:44 PM
Replies: 1
Views: 1,279
Posted By Sk8ermane

Bad idle surge, running really rich, code 14 on an lsvtec

After tons of fitment problems, I got to finally crank it, and it was billowing smoke from unburnt fuel. It set off a code 14, but I know the iacv is good because I was using it two days ago, but...
Forum: Hybrid / Engine Swaps
02-12-2008, 02:12 AM
Replies: 7
Views: 1,712
Posted By Sk8ermane

Re: Setting the rev limmiter on ls/vtec (tripledubz)

That's what I am thinking. I was told by so many people that it is safe to take it to 7,200, and a few said 7,400, but I don't want to risk my bottom end over a couple hundred rpm's you know? It's in...
Forum: Hybrid / Engine Swaps
02-10-2008, 09:02 PM
Replies: 7
Views: 1,712
Posted By Sk8ermane

Setting the rev limmiter on ls/vtec

I am putting a gsr head on my car next week and I need to know what to set the rev limiter at. I have done some reading here and there about the rod bolts stretching around 7,000 rpm's. I don't have...
Forum: Hybrid / Engine Swaps
01-11-2008, 08:59 AM
Replies: 1
Views: 401
Posted By Sk8ermane

Re: The code 43 paradox (Sk8ermane)

I guess nobody knows or cares to help me on this board. Thanks anyway's though.
Forum: Hybrid / Engine Swaps
01-04-2008, 02:55 PM
Replies: 1
Views: 401
Posted By Sk8ermane

The code 43 paradox

Not really much of a paradox, but I have read that alcohol does not damage 02 sensors and I was steam cleaning my motor with some alcohol by misting it into the throttlebody, and although it runs...
Forum: Hybrid / Engine Swaps
01-04-2008, 01:52 PM
Replies: 1
Views: 381
Posted By Sk8ermane

Re: NEED HELP on LS swaps EXHAUST SYSTEM in 94 civic!! (Lee_eg6si)

So you have stock exhaust on an ls swap?

If that's the case, then I would just buy some exhaust pipe from a muffler shop with all the nessesary flanges,gaskets,hangers and bends and do a custom...
Forum: Hybrid / Engine Swaps
12-25-2007, 01:12 PM
Replies: 6
Views: 1,801
Posted By Sk8ermane

Re: (snowseeker)

I tried to re-do it again today, but no luck. It looks almost dead on, but there is definitly still something off. As far as power goes, it has a surge of midrange torque between 4,000-5,500, and...
Forum: Hybrid / Engine Swaps
12-25-2007, 06:01 AM
Replies: 6
Views: 1,801
Posted By Sk8ermane

Timing off by 1/2 tooth due to head milling (need advice from expert on engine combustion)

OK, I bought this b18b motor for my civic a while back and it never ran right. The cam timing was off everytime. So, after a while, I came to notice that no matter which way I would set the cam...
Forum: Hybrid / Engine Swaps
07-04-2007, 10:45 AM
Replies: 28
Views: 118,307
Posted By Sk8ermane

Re: (Sk8ermane)

Anyone?
Forum: Hybrid / Engine Swaps
07-02-2007, 02:52 PM
Replies: 28
Views: 118,307
Posted By Sk8ermane

Re: (Sk8ermane)

Also, what about the fuel pump? Do I need to upgrade or rewire it or anything?
Forum: Hybrid / Engine Swaps
06-30-2007, 06:48 PM
Replies: 28
Views: 118,307
Posted By Sk8ermane

I almost have all the parts for the swap. I have...

I almost have all the parts for the swap. I have to find a cheap place to find the axles and intermediate shaft, but after that its a matter of little things like header and exhaust.

I have a few...
Forum: Hybrid / Engine Swaps
06-21-2007, 10:13 PM
Replies: 1
Views: 305
Posted By Sk8ermane

Questioning the strength of an Ls bottom end

I bought a b18b to put in my 94 civic ex because I spun a rod bearing with my d16. Here is my question. This motor has a 123,000 miles on it, and allthough it is clean, and it runs good, the guy who...
Forum: Hybrid / Engine Swaps
06-16-2007, 03:23 AM
Replies: 49
Views: 5,889
Posted By Sk8ermane

Re: (HondaBurger)

I am in the process of swaping an ls motor in my 94 civic ex. I want to put a gsr head on later on this year when I get more money but I hear that the ls block doesnt like to rev as high because of...
Forum: Honda Civic / Del Sol (1992 - 2000)
06-13-2007, 08:51 AM
Replies: 2
Views: 309
Posted By Sk8ermane

Looking for an ls swap

My d16 spun a rod bearing the other day and I am looking for an ls swap. Does anyone know where is the best place to look for something like that? I am also curious on what price is considered fair...
Showing results 1 to 17 of 17


 
Forum Jump


All times are GMT -8. The time now is 07:05 AM.