Honda-Tech - Honda Forum Discussion

Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: skrewdlude
Showing results 1 to 25 of 490
Search took 2.36 seconds.
Forum: Honda Prelude
01-11-2014, 05:58 AM
Replies: 2
Views: 4,382
Posted By skrewdlude

Re: vtec solenoid

Between the cylinder header, and the vtec unit, is the spool valve gasket/filter assembly.

In this picture: http://www.hondaautomotiveparts.com/auto/jsp/mws/catimgs/13ss001_e1002.png

Spool...
Forum: Honda Prelude
01-11-2014, 05:42 AM
Replies: 2
Views: 2,070
Posted By skrewdlude

Re: h22a1 dowel pin size?

The two dowels between the head and block are 14mm x 20mm, Honda part number: 94301-14200. If your local Honda happens to be out, just order them at an online honda store like majestic honda.
Forum: Honda Prelude
01-10-2014, 03:07 PM
Replies: 4
Views: 642
Posted By skrewdlude

Re: headers h23av?

Any standard H22 header should work. The blue top uses the H22 head.
Forum: Honda Prelude
01-11-2009, 09:49 AM
Replies: 5
Views: 1,071
Posted By skrewdlude

Re: after swap- no tach!?!?

Also, near the passenger side wheel well ( in the engine bay), there is a capped blue wire. It is a test tach lead, check the voltage there, easier than pulling apart the dizzy usually.
Forum: Honda Prelude
04-01-2008, 05:21 AM
Replies: 6
Views: 3,747
Posted By skrewdlude

Re: p28 in prelude? (boostedh22lude1)

You don't have to swap anything. The pin out is the same between a p28/p13/p14/p72/ etc... You are throwing an o2 code because A6 is the O2 heating wire, and you swapped it with a11, which is the...
Forum: Honda Prelude
02-01-2008, 07:49 AM
Replies: 6
Views: 923
Posted By skrewdlude

Re: Are there any accessory (integra15)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by integra15 &raquo;</TD></TR><TR><TD CLASS="quote">I beleive there should be. If there are they should...
Forum: Honda Prelude
01-21-2008, 07:07 AM
Replies: 209
Views: 76,797
Posted By skrewdlude

Re: (mgags7)

I played with adjusting it when i first did the conversion, and I was able to dial out a lot of the play. I know i need new wheel bearings; so I plan to try adjusting it again once i replace those....
Forum: Honda Prelude
01-20-2008, 08:40 PM
Replies: 1
Views: 896
Posted By skrewdlude

Re: 5th Generation Prelude Carputer (spike1202)

Can't see the install because i don't have a yahoo account, and it is asking me to sign in. I would, however, suggest heading over to http://www.mp3car.com if you haven't already. You will...
Forum: Honda Prelude
01-09-2008, 05:55 PM
Replies: 22
Views: 1,583
Posted By skrewdlude

Re: (.Hatches.)

Just to correct what i was saying, for the h22a4 rail to work, you would need the fuel line that runs from fuel filter to fuel rail from a h22a4 engine. As it is longer, and attaches on the far end...
Forum: Honda Prelude
01-09-2008, 03:57 PM
Replies: 22
Views: 1,583
Posted By skrewdlude

Re: (.Hatches.)

I know an h22a1 rail will fit no problem, but i can not say for sure if a H22A4. The H22a1, and H22a4 fuel rails are different part numbers.
I think the a4 rail will work with a custom fuel line....
Forum: Honda Prelude
01-08-2008, 09:51 PM
Replies: 22
Views: 1,583
Posted By skrewdlude

Re: RC injectors (97 Sleeper)

Also, i forgot to answer your question regarding the clips. No, they don't come with the injectors, unless it actually states it is including them. The clips are about $10 a piece at most places. ...
Forum: Honda Prelude
01-08-2008, 09:28 PM
Replies: 22
Views: 1,583
Posted By skrewdlude

Re: RC injectors (97 Sleeper)

Both are fine for boost. Without getting to technical on the difference... which injectors you go with will come down to your fuel requirements. I think the biggest saturated injector RC makes is a...
Forum: Honda Prelude
01-08-2008, 06:34 PM
Replies: 22
Views: 1,583
Posted By skrewdlude

Re: RC injectors (97 Sleeper)

Going by your name, I am assuming you have a 5th gen, and for a 5th gen you need to have the injector clips for any non OEM injectors.
Forum: Honda Prelude
01-06-2008, 10:20 PM
Replies: 209
Views: 76,797
Posted By skrewdlude

Re: (Hawkze_2.3)

My rack is still holding up great. I replaced my inner and outer tie rods when doing the conversion originally, and i still had some play. I tried a few different tensions on the adjuster, and was...
Forum: Honda Prelude
12-17-2007, 07:42 AM
Replies: 26
Views: 5,650
Posted By skrewdlude

Re: (mgags7)

I had a start up issue with my original fidanza, which was purchased almost 7 years ago. I called them, and it turns out they revised the design and notched the teeth as well as added the bearing. ...
Forum: Forced Induction
11-30-2007, 12:12 PM
Replies: 62
Views: 6,478
Posted By skrewdlude

Re: (m R g S r)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by m R g S r &raquo;</TD></TR><TR><TD CLASS="quote">
Can't be that old because of the logo cnc'ed on...
Forum: Forced Induction
11-30-2007, 10:48 AM
Replies: 62
Views: 6,478
Posted By skrewdlude

Re: (Danny_EJ)

I have had mine for over 2 yrs now, and it is going strong. Benson, CP, and Pauter. https://honda-tech.com/forums/images/smilies/emsmile.gif Laskey Racing is awesome, ridiculously helpful. I never...
Forum: Honda Prelude
09-23-2006, 11:22 AM
Replies: 11
Views: 2,122
Posted By skrewdlude

Re: Removing the IAB's.... (bluedlude)

Removing the valves and leaving the spacer in there, and unplugging the hose have the same effect. You will get turbulence by leaving the valves and shaft in, but its not a dramatic difference. I...
Forum: Honda Prelude
07-05-2006, 10:59 PM
Replies: 12
Views: 741
Posted By skrewdlude

Re: (prayludin)

Considering they say "Prime Wheel Corp." I am going to go out on a limb here and say they are Prime Wheels (http://www.primewheel.com/) https://honda-tech.com/forums/images/smilies/emsmilep.gif
Forum: Honda Prelude
06-22-2006, 01:16 PM
Replies: 3
Views: 582
Posted By skrewdlude

Re: Fixed back style corbeau racing seats... (egcoupe94)

No Racing seat I have ever sat in has a 90 degree angle on the seat back. I have sparcos, and they are slightly angled back. It is a comfortable position.
Also, the head room depends on how they...
Forum: Forced Induction
05-31-2006, 10:50 AM
Replies: 3,383
Views: 216,270
Posted By skrewdlude

Re: (ben@importparts.com)

Upgrade ordered, thanks Ben https://honda-tech.com/forums/images/smilies/emthup.gif
Forum: Honda Prelude
05-30-2006, 09:03 AM
Replies: 3
Views: 397
Posted By skrewdlude

Re: Problems with JDM H22 (beqa16v)

You sure everything was lined up when you put the belt on, and did you check your timing with a light?
Forum: Forced Induction
05-24-2006, 08:07 PM
Replies: 7
Views: 2,080
Posted By skrewdlude

Re: Oil Pressure ports (92hondalude)

He got it with the fmax kit. It is -3, and about 2-3ft long. You can make your own at Summit Racing, or an-plumbing.com
Forum: Honda Prelude
05-18-2006, 10:41 PM
Replies: 24
Views: 4,686
Posted By skrewdlude

Re: (M@)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by M@ &raquo;</TD></TR><TR><TD CLASS="quote">I'm alittle shocked no one has pimped the groundcontrol...
Forum: Honda Prelude
05-06-2006, 07:55 PM
Replies: 20
Views: 1,664
Posted By skrewdlude

Re: Distributor cap for JDM H22?? (---+)

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by ---+ &raquo;</TD></TR><TR><TD CLASS="quote">accord 90-93 cap
civic 92-95 rotor</TD></TR></TABLE>
...
Showing results 1 to 25 of 490
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 08:16 PM.