David B Loftus

I've done my swap but the car is not getting fuel or spark due to I don't know how to wire in the neutral safety switch or clutch switch

xhndapwrx

This may have came around before and yes I tried the search thanks. So I received a h22a swapped 92-95 civic hatch from a buddy and I want to replace the intake manifold with a skunk2. My question is, do I need to remove the whole motor to get the job done due to clearance issues? Thanks

JRCivic1

Do you have a "straight H" swap or an H2B swap ?

xhndapwrx

Straight H swap.

JRCivic1

It doesn't fit without making contact with the brake lines on the firewall... or maybe even the firewall itself depending on the mounts used. Stick with the H22 Intake manifold... it works much better.

xhndapwrx

Thank you.

VINNY.YZ

I Have an Obd2 H22a and i am running a p28 so i can tune the car. Now i need to get emissions done on it and i am wondering what ecu can i use to allow the scanner port in the car to work. (the car is an 01 integra so it has an obd2 plug).

Asantiago101

Ok I have a accord euror with a H22a having problems bogging in take off. It completely looses power, doesn’t shut off but very hesitant, then clears and catches up. I’ve changed a lot, fuel pump, did timing about 6 months ago, icm in dizzy and coil changed plugs, did a compression test was at 240psi and after 2 cylinder it blew out my dads gauge, got another and all 4 read 160psi. Any advice?

Krut

Maybe get the injectors flow tested/cleaned and check/replace the fuel filter? Did the car ever sit for a long time? I had an intermittent bogging issue and it ended up being rusty debris in the tank clogging up the fuel pump sock, replaced the whole fuel tank. Something to check.

Asantiago101

I changed fuel pump and sock. It doesn’t have any other additional filter on the car it’s a JDM accord euror I haven’t removed the injectors though. Might have to try that. I did purchase a royal purple fuel treatment someone else suggested to try. Hope it’s not the tank….

6942069

anybody know about an h22a4 head on an f22b1 block? would it be worth it if it did work well? would i need pistons? im a novice be patient with my autism.

Mrchan

hey, so technically, its more of an f series question being that i got an f20b. BUT with months and months of research, i find out its basically an h22. anyways, what rear mounting bracket would i use for the f2b(h2b) swap in a 92 civic hatch? i got a 94 gsr transmission with a 1320 h2b kit.

Reddot

What harness do I need for my h22a engine in 96 accord ex with vtech

JRCivic1

You use the '96 Accord engine harness and modify it to fit the H22A engine.

Reddot

Looking to buy a new one mine is a mess

JRCivic1

A brand new OE harness is long discontinued... and thus, unavailable. All you can do is either hunt down a used one that is in better condition than yours or repair the damaged areas of your own as you modify it for the H22A.

4doorjohnny

Having an issue with the idle being raised while coasting at low speeds or parking. It’s like the iACV is staying open and adding throttle when I don’t want it to.

JRCivic1

It is normal to have a slightly elevated idle speed when the vehicle is moving... it should slowly drop to normal idle once you come to the stop.

Favio L. Torres

Hello Guys,
My engine is H22A, I need to replace crankshaft because main and rod bearings has wear and already are +50mm.

Another option would be find main rod bearing kit to +0.75mm for all 16 pieces, does anyone knows where to find them?

Favio +504-3164-9445 whatsapp