YAY! it runs.....SNAP!
#1
Honda-Tech Member
Thread Starter
Join Date: Jun 2004
Location: Land Of Theives, U.S.A.
Posts: 5,634
Likes: 0
Received 0 Likes
on
0 Posts
YAY! it runs.....SNAP!
ok well i just started my crx after like a year and i just put my stock motor in. well it started i was happy then i was giving it alittle gas and then it died. just died. no noise no nuthing. well i went to look what happend and the timing belt snapoed. any damage? it was at like 2K rpm when it died. please let me know if u guys have had this happen. also how hard is it to replace the timing belt?
-Kyle
-Kyle
#2
Join Date: Feb 2005
Location: Arlington, Wa, United States
Posts: 228
Likes: 0
Received 1 Like
on
1 Post
Re: YAY! it runs.....SNAP! (H4 Project)
you could be lucky. without pulling anything, just replace the timing belt, make sure you have everything set correctly and then try to fire it up again. that would be the least invasive way.
#4
Honda-Tech Member
Join Date: Apr 2003
Location: Kona/V-town, HI
Posts: 2,776
Likes: 0
Received 0 Likes
on
0 Posts
Re: YAY! it runs.....SNAP! (H4 Project)
yup. my motor when i bought my car busted the timing belt but the girl tried to start it after she broke the timing belt. bent valves in 2 cylinders
#5
Honda-Tech Member
Thread Starter
Join Date: Jun 2004
Location: Land Of Theives, U.S.A.
Posts: 5,634
Likes: 0
Received 0 Likes
on
0 Posts
Re: YAY! it runs.....SNAP! (civickiller)
i havnt tried turning it over since. when it died i saw the belt was broke and just walked inside. so is there a chance there is no damage?
-Kyle
-Kyle
#6
Honda-Tech Member
Join Date: Apr 2003
Location: Kona/V-town, HI
Posts: 2,776
Likes: 0
Received 0 Likes
on
0 Posts
Re: YAY! it runs.....SNAP! (H4 Project)
maybe depends on the position of the cam. if the cam is at the right spot with hardly any of the valves being open then you can spin the crank as much as you want and it wont hit. low compression with a small cam has better odds of not bending a valve. best bet is to just stick another timing belt on there and try and start it.
Trending Topics
#8
Honda-Tech Member
Join Date: Feb 2005
Location: Riverside
Posts: 2,002
Likes: 0
Received 0 Likes
on
0 Posts
Re: YAY! it runs.....SNAP! (H4 Project)
From my experiences when stock single cams belts snapped there is a high chance that nothing happened. But if it happened to a b-series you can kiss your valves good bye. Best of luck to you cause I felt that pain.
#11
Honda-Tech Member
Join Date: Dec 2005
Location: SoCal Pram Hok Pi
Posts: 1,259
Likes: 0
Received 0 Likes
on
0 Posts
Re: (Tippyman)
You might have a couple of bent valves. I had my timing belt snap on me on the freeway. When I took off the head, I noticed I had 4 bent valves.
#12
Honda-Tech Member
Thread Starter
Join Date: Jun 2004
Location: Land Of Theives, U.S.A.
Posts: 5,634
Likes: 0
Received 0 Likes
on
0 Posts
Re: (Smash03)
wel i was just sitting in it. the shift linkage isnt even hooked up so it wasnt in gear or moving anywhere. i tapped teh gas a few times and the rpm went up to about 2K so im hoping that nothing happend.......also where is teh ELD sensor located? im throwing a code 20....and 6
-Kyle
-Kyle
#13
Honda-Tech Member
Thread Starter
Join Date: Jun 2004
Location: Land Of Theives, U.S.A.
Posts: 5,634
Likes: 0
Received 0 Likes
on
0 Posts
Re: YAY! it runs.....SNAP! (H4 Project)
o also. i didnt hear any noise when it snapped. it sounded liek it just died no bang or knock or anything. and luckly i didnt try to restart it. LOL!
Thread
Thread Starter
Forum
Replies
Last Post
soodominican
Honda CRX / EF Civic (1988 - 1991)
9
10-12-2008 08:59 PM
verycleanhatch
Honda Civic / Del Sol (1992 - 2000)
6
06-20-2006 05:29 PM