I am still stumped, injectors won't fire.
#1
Honda-Tech Member
Thread Starter
Join Date: Oct 2005
Location: Portsmouth, va, united states
Posts: 488
Likes: 0
Received 0 Likes
on
0 Posts
I am still stumped, injectors won't fire.
I started a couple of other threads a couple of months ago, but nothing has worked.
Info:
89 crx
b16
obd0
My injectors are not firing. I have checked continuity. I have 2 ecu's (pr3 and pwo) and get the same results with both. I replaced my crank angle sensor pins and she fired up, but only ran for 10 minutes and shut off. Hasn't started since. I am getting zero codes.
I am stumped, I really don't want to start throwing parts at it, but I really am at a loss. I need a list of reasons of what would cause the pulse to not be sent to the injectors.
In the other thread someone mention it could be a bad ground, where would I find the ground that controls the injector pulse?
Info:
89 crx
b16
obd0
My injectors are not firing. I have checked continuity. I have 2 ecu's (pr3 and pwo) and get the same results with both. I replaced my crank angle sensor pins and she fired up, but only ran for 10 minutes and shut off. Hasn't started since. I am getting zero codes.
I am stumped, I really don't want to start throwing parts at it, but I really am at a loss. I need a list of reasons of what would cause the pulse to not be sent to the injectors.
In the other thread someone mention it could be a bad ground, where would I find the ground that controls the injector pulse?
Last edited by crxmadness; 03-01-2013 at 09:25 PM.
#2
#3
Honda-Tech Member
Thread Starter
Join Date: Oct 2005
Location: Portsmouth, va, united states
Posts: 488
Likes: 0
Received 0 Likes
on
0 Posts
Re: I am still stumped, injectors won't fire.
#4
Honda-Tech Member
Re: I am still stumped, injectors won't fire.
So was it running fine before? Or did you just do the swap?
Any CEL codes coming up?
Do you have obd0 injectors or obd1? Are you using the resisitor box?
The ground to check is on the thermostat housing.
Any CEL codes coming up?
Do you have obd0 injectors or obd1? Are you using the resisitor box?
The ground to check is on the thermostat housing.
#6
Honda-Tech Member
Thread Starter
Join Date: Oct 2005
Location: Portsmouth, va, united states
Posts: 488
Likes: 0
Received 0 Likes
on
0 Posts
Re: I am still stumped, injectors won't fire.
It was running fine before, one day it just shut off. Did some tests and found out the injectors were not firing.
no cels
obd0 and yes running resistorbox
scuffed up the ground on the thermostat and bolted it back down
#7
Honda-Tech Member
Thread Starter
Join Date: Oct 2005
Location: Portsmouth, va, united states
Posts: 488
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#9
PHANTOM MENACE
iTrader: (2)
Join Date: May 2005
Location: SYCUAN NINE, CA, USA
Posts: 6,042
Likes: 0
Received 3 Likes
on
3 Posts
Re: I am still stumped, injectors won't fire.
I recently just experienced the same issue. I got to the point where I was ready to rip out the wiring harness and start manually tracing where the power/continuity stops between the main relay and injectors. I got it running a couple of days ago, problem was my distributor. More specifically the sensors integrated into the distributor (cam and crank position sensor I believe). The coil and ignitor were both replaced with new not used units and it still wouldn't start so I figured the issue was else where until my buddy loaned me an extra distributor.
My thread is a couple pages back now if you wanna read and see the trouble shooting process.
My thread is a couple pages back now if you wanna read and see the trouble shooting process.
#10
Honda-Tech Member
Thread Starter
Join Date: Oct 2005
Location: Portsmouth, va, united states
Posts: 488
Likes: 0
Received 0 Likes
on
0 Posts
Re: I am still stumped, injectors won't fire.
I recently just experienced the same issue. I got to the point where I was ready to rip out the wiring harness and start manually tracing where the power/continuity stops between the main relay and injectors. I got it running a couple of days ago, problem was my distributor. More specifically the sensors integrated into the distributor (cam and crank position sensor I believe). The coil and ignitor were both replaced with new not used units and it still wouldn't start so I figured the issue was else where until my buddy loaned me an extra distributor.
My thread is a couple pages back now if you wanna read and see the trouble shooting process.
My thread is a couple pages back now if you wanna read and see the trouble shooting process.
https://honda-tech.com/forums/honda-crx-ef-civic-1988-1991-3/1991-honda-civic-no-start-condition-3101841/
#11
Honda-Tech Member
Thread Starter
Join Date: Oct 2005
Location: Portsmouth, va, united states
Posts: 488
Likes: 0
Received 0 Likes
on
0 Posts
Re: I am still stumped, injectors won't fire.
U da man 24TEN I bought a brand new td22u distributor andi havent had a problem since!
Thread
Thread Starter
Forum
Replies
Last Post
caspers_hatch
Hybrid / Engine Swaps
6
02-27-2005 11:47 PM