brokenojoke

I'm using hasport mounts and a full-race front crossmember with stock DA dual core full size radiator that's slanted back slightly.

Thanks

brokenojoke

I wanted to know if the header hits the radiator at all.... Is there going to be a need for a 1/2 radiator?

Super Chicken

I have a B18 and a DA radiator and my Hytech replica clears with plenty of room in fact I should be able to install my condensor fan as well!!!

brokenojoke

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Super Chicken &raquo;</TD></TR><TR><TD CLASS="quote">I have a B18 and a DA radiator and my Hytech replica clears with plenty of room in fact I should be able to install my condensor fan as well!!!</TD></TR></TABLE>

Which mount kit you using?

brokenojoke

Anyone else that can verify what mounts they were using when it fit?

Thanks.

SIred91

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by brokenojoke &raquo;</TD></TR><TR><TD CLASS="quote">Anyone else that can verify what mounts they were using when it fit?

Thanks. </TD></TR></TABLE>

They are all so close it wont matter.

jdmoptiontune

I have a crx with hytech knock off, full-race tb, and stock radiator. Everything clears fine. Oh yeah and hasport mounts, but I do need an sir hood cuz I can't shut mine all the way

Khmi

B18c1, Hasport mounts, Hytech replica, Innovative traction bar, and stock radiator. Clears stock fan too. Heres a pic:

Super Chicken

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by brokenojoke &raquo;</TD></TR><TR><TD CLASS="quote">

Which mount kit you using? </TD></TR></TABLE>

Innovative

mullet eater

I have place racing mounts with a b16 and a koyo 2 core radiator and a place racing traction bar and the stock exhaust manifold is too close for comfort. I would like to know if that same setup would fit a koyo 2 core radiator? does anybody have pictures with one?


Modified by mullet eater at 7:15 PM 5/13/2008

StorminMatt

When it comes to header clearance, the radiator is not the problem. The crossmember is.

Bob_760

Do you guys think this would fit? It looks like it might from the pics.

I have hasports which should put the engine further back comparatively but my car is in pieces and I put these fans on then suddenly realized I'm not certain it'll fit.

stunn'd

I doubt that'll clear with the drivers side fan on there

gursh d

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Khmi &raquo;</TD></TR><TR><TD CLASS="quote">B18c1, Hasport mounts, Hytech replica, Innovative traction bar, and stock radiator. Clears stock fan too. </TD></TR></TABLE>

I'm assuming all Hytech replica's are the tri-design. What's your ground clearance like? Is your car dropped at all, or are your riding stock height?

Bob_760

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by stunn’d &raquo;</TD></TR><TR><TD CLASS="quote">I doubt that'll clear with the drivers side fan on there</TD></TR></TABLE>

That's what I'm afraid of... oh well... we'll see...

jdm_dc_fan

iTrader: (1)

it will clear easy.

brokenojoke

It does fit with no problem. I removed the inlet/outlet for the unused tranny cooler to make for ease of install. It fit without cutting it, but it only had like a 1/16 till it hit. It didn't come with the bolts that hold the two pieces together though.
It didn't come with the flange for the extention pipe either.... I figured it would have.

Other than that it looks good. Can't wait to dyno it.



Modified by brokenojoke at 2:41 AM 5/15/2008

jdm_dc_fan

iTrader: (1)

told you