apexi ws2 hangs low, cutting resinator too loud?
#1
Honda-Tech Member
Thread Starter
apexi ws2 hangs low, cutting resinator too loud?
ok so my apexi ws2 resonator hangs really low..
im going to go to a muffler shop tomoro to see if they can tuck it up better but if they cant,
how much louder would it be if i cut out the resonator and weld in straight pipe in that section?
right now you can barely hear it i have my stock headers and cat..
im going to go to a muffler shop tomoro to see if they can tuck it up better but if they cant,
how much louder would it be if i cut out the resonator and weld in straight pipe in that section?
right now you can barely hear it i have my stock headers and cat..
#3
The Grumpiest
iTrader: (4)
Join Date: May 2008
Location: Oak Ridge, TN, USA
Posts: 28,333
Likes: 0
Received 16 Likes
on
15 Posts
Re: apexi ws2 hangs low, cutting resinator too loud?
This is what happens when you have to have "Moar Low". First it was the oil pan and now this.
Cut off the resonator and there goes your quiet exhaust and you realize you could have bought an Ebay exhaust for less.
Cut off the resonator and there goes your quiet exhaust and you realize you could have bought an Ebay exhaust for less.
#5
The Grumpiest
iTrader: (4)
Join Date: May 2008
Location: Oak Ridge, TN, USA
Posts: 28,333
Likes: 0
Received 16 Likes
on
15 Posts
Re: apexi ws2 hangs low, cutting resinator too loud?
How would I know? I don't know of anyone that buys a complete exhaust system only to then hack it all to hell because they failed to plan for how low the car was going to be.
That's what you get when you have to follow trends.
That's what you get when you have to follow trends.
#6
Honda-Tech Member
Join Date: Sep 2010
Location: Pensacola, FL and every Court House in Louisiana
Posts: 3,114
Likes: 0
Received 2 Likes
on
2 Posts
Re: apexi ws2 hangs low, cutting resinator too loud?
If you go to the muffler shop just have them make a new pipe for that section that way you can always go back and don't ruin your whole exhaust. It should be no more than 80 bucks.
Trending Topics
#8
Honda-Tech Member
Thread Starter
Re: apexi ws2 hangs low, cutting resinator too loud?
#11
Honda-Tech Member
Join Date: Oct 2007
Location: Dub Caesar, PA
Posts: 1,644
Likes: 0
Received 0 Likes
on
0 Posts
Re: apexi ws2 hangs low, cutting resinator too loud?
I suggest to get under the car and inspect the rubber bushings. I went through a bushing every 3 months when I first installed my WS2. It kept ripping in the middle. Found some slightly shorter urethane exhaust bushings on eBay and they have been holding up fine for the past 2-3 years.
#12
Re: apexi ws2 hangs low, cutting resinator too loud?
I guess people are going to ignore this person??
I suggest to get under the car and inspect the rubber bushings. I went through a bushing every 3 months when I first installed my WS2. It kept ripping in the middle. Found some slightly shorter urethane exhaust bushings on eBay and they have been holding up fine for the past 2-3 years.
I suggest to get under the car and inspect the rubber bushings. I went through a bushing every 3 months when I first installed my WS2. It kept ripping in the middle. Found some slightly shorter urethane exhaust bushings on eBay and they have been holding up fine for the past 2-3 years.
#14
B*a*n*n*e*d
Join Date: Feb 2008
Location: Charlottesville, VA, USA
Posts: 6,420
Likes: 0
Received 5 Likes
on
5 Posts
Re: apexi ws2 hangs low, cutting resinator too loud?
I guess people are going to ignore this person??
I suggest to get under the car and inspect the rubber bushings. I went through a bushing every 3 months when I first installed my WS2. It kept ripping in the middle. Found some slightly shorter urethane exhaust bushings on eBay and they have been holding up fine for the past 2-3 years.
I suggest to get under the car and inspect the rubber bushings. I went through a bushing every 3 months when I first installed my WS2. It kept ripping in the middle. Found some slightly shorter urethane exhaust bushings on eBay and they have been holding up fine for the past 2-3 years.
#16
Honda-Tech Member
iTrader: (1)
Join Date: Feb 2011
Location: Jersey
Posts: 863
Likes: 0
Received 0 Likes
on
0 Posts
Re: apexi ws2 hangs low, cutting resinator too loud?
Make sure the mid-pipe isn`t upside down....if you go and cut a $500 exhaust because you didn`t compensate for the exhaust when you lowered you car, than I`m sorry, you sir are an idiot...Just my 2-cents.
#17
Honda-Tech Member
Thread Starter
Re: apexi ws2 hangs low, cutting resinator too loud?
well i have the same exhaust on my eg and for some reason it hangs lower on the ek, so i guess im an idiot.. and the mid pipe is on right
#18
Honda-Tech Member
Thread Starter
Re: apexi ws2 hangs low, cutting resinator too loud?
hey do you think if i put my stock exhaust back on it will fit with the axle back to the worldsport muffler?? or would it not work because its 2 different sizes?
#19
Honda-Tech Member
Thread Starter
Re: apexi ws2 hangs low, cutting resinator too loud?
sorry guys im not hitting my oil pan after all.. its my apexi ws2.. **** hangs low.. i got the pipe bent up a little at a muffler shop but still hits the huge resinator sometimes so i might just cut it out and put a straight pipe there..
#21
Honda-Tech Member
iTrader: (1)
Re: apexi ws2 hangs low, cutting resinator too loud?
^Agreed. At least just get a section made to completely replace that part of the piping so you can go back when you don't care for it. Its almost straight through there.
As far as hardly being able to hear it as it is... If you wanted a loud exhaust, why would you buy a WS2? I loved that I couldn't even tell mine was there when the car was still stock. I can't wait to be done with my break in so I can put a cat on it and be back to that point.
The resonator does hang pretty low on mine though, I need to look into those poly hangers more, I had seen them but I wasn't sure if they would actually make a difference.
As far as hardly being able to hear it as it is... If you wanted a loud exhaust, why would you buy a WS2? I loved that I couldn't even tell mine was there when the car was still stock. I can't wait to be done with my break in so I can put a cat on it and be back to that point.
The resonator does hang pretty low on mine though, I need to look into those poly hangers more, I had seen them but I wasn't sure if they would actually make a difference.
#23
Honda-Tech Member
Thread Starter
Re: apexi ws2 hangs low, cutting resinator too loud?
[QUOTE=spAdam;47366442]^Agreed. At least just get a section made to completely replace that part of the piping so you can go back when you don't care for it. Its almost straight through there.
No its different on the ek hatch theres the first pipe from the header cuz the hatchbacks have the cat in the header so theres a seperate pipe for that and then is the resinator which curves back to the axle back
No its different on the ek hatch theres the first pipe from the header cuz the hatchbacks have the cat in the header so theres a seperate pipe for that and then is the resinator which curves back to the axle back