Clean OBD1 B18C Integra GSR Longblock/Swap
#1
Honda-Tech Member
Thread Starter
Join Date: Sep 2008
Location: Racine, Wisconsin, United States
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
Clean OBD1 B18C Integra GSR Longblock/Swap
Selling a great looking OBD1 GSR motor. Motor has ~70k on it and was very well maintained, great compression across the board. Internally the motor is completely stock, I am the second owner, its not some ***** motor that's been taken apart by every retarded kid in the area. I just put in a lot of time into this motor and it shows. Trying to sell the longblock at this point but I can sell the whole swap (S80 trans is not currently as pretty as the motor), have harness, axels, ecu etc. Also should have a stock exhaust manifold on it at some point this week.
-fresh valve adjustment
-block freshly painted (everything painted properly with the right paint, tons of time into surface prep)
-water pipe, thermostat housing, alternator brackets, and all other brackets freshly painted
-oil pain freshly painted, brand new oil pan gasket (genuine honda)
-Timing cover refreshed (plastic shines like new, no paint)
-Valve cover freshly painted a custom blue shade, its very close to the j's racing color. Pics do not do the cover any kinda of justice, terrible lighting + iPhone camera
-New OE Honda valve cover gasket, spark plug seals, grommets & acorn nuts
-Skunk2 intake manifold port matched to 70mm Prof. Prod. Throttle body
-Stock gsr injectors rebuilt by RC (have receipt & flow report)
-Blox thermal IM gasket
-BRAND NEW Blox tps sensor (all other sensors included)
-CTR crank pulley -Dizzy/alternator included
I'm sure I'm leaving things out. If interested send me an email @nathanfolks@gmail.com or text me at 262-902-9750 for fastest response. Please don't ask a million questions I explained it pretty thoroughly. I do not want trades, cash only. 1300 listed is for longblock only, if interested in whole swap a price can be discussed pending progress on transmission. I will entertain offers but like I said I have a TON of time and a fair amount of money into this motor. Thanks for checking it out.
-fresh valve adjustment
-block freshly painted (everything painted properly with the right paint, tons of time into surface prep)
-water pipe, thermostat housing, alternator brackets, and all other brackets freshly painted
-oil pain freshly painted, brand new oil pan gasket (genuine honda)
-Timing cover refreshed (plastic shines like new, no paint)
-Valve cover freshly painted a custom blue shade, its very close to the j's racing color. Pics do not do the cover any kinda of justice, terrible lighting + iPhone camera
-New OE Honda valve cover gasket, spark plug seals, grommets & acorn nuts
-Skunk2 intake manifold port matched to 70mm Prof. Prod. Throttle body
-Stock gsr injectors rebuilt by RC (have receipt & flow report)
-Blox thermal IM gasket
-BRAND NEW Blox tps sensor (all other sensors included)
-CTR crank pulley -Dizzy/alternator included
I'm sure I'm leaving things out. If interested send me an email @nathanfolks@gmail.com or text me at 262-902-9750 for fastest response. Please don't ask a million questions I explained it pretty thoroughly. I do not want trades, cash only. 1300 listed is for longblock only, if interested in whole swap a price can be discussed pending progress on transmission. I will entertain offers but like I said I have a TON of time and a fair amount of money into this motor. Thanks for checking it out.
Last edited by raytownracer; 09-27-2011 at 07:24 AM.
#7
Honda-Tech Member
Thread Starter
Join Date: Sep 2008
Location: Racine, Wisconsin, United States
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
Re: Clean OBD1 B18C Integra GSR Longblock/Swap
Brand spankin new. However there was a chip in it from me dropping it a while back, i ground the sharp edge down and it wont catch the belt. The chip doesn't effect performance at all. And I have the original pulley with accessory ribs if you'd rather take that.
Trending Topics
#8
Honda-Tech Member
Thread Starter
Join Date: Sep 2008
Location: Racine, Wisconsin, United States
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
#14
Honda-Tech Member
Join Date: Oct 2008
Location: waukegan il
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Re: Clean OBD1 B18C Integra GSR Longblock/Swap
#15
Honda-Tech Member
Thread Starter
Join Date: Sep 2008
Location: Racine, Wisconsin, United States
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
#20
Honda-Tech Member
Thread Starter
Join Date: Sep 2008
Location: Racine, Wisconsin, United States
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
Re: Clean OBD1 B18C Integra GSR Longblock/Swap
BUMP!!
Price Drop. $1400 for longblock, $2000 for Complete swap. Come on people this is a bargain. Just the intake manifold/tb on this motor is easily worth $350. I need this thing gone.
Price Drop. $1400 for longblock, $2000 for Complete swap. Come on people this is a bargain. Just the intake manifold/tb on this motor is easily worth $350. I need this thing gone.
Thread
Thread Starter
Forum
Replies
Last Post