Intake manifold torque specs? - Honda-Tech


Intake manifold torque specs?

Reply
 
 
 
LinkBack Thread Tools Search this Thread
Old 01-17-2008, 04:50 PM   #1
Thread Starter
 
dballard's Avatar
 
Join Date: Oct 2007
Location: Edmeston, NY
Posts: 10
Default Intake manifold torque specs?

I'm about to finish up installing the IMG. I've searched for quite some time now and cannot find the torque specs for the bolts that hold the manifold to the head. I have found where one person didn't torque it down enough and ended up ruining their motor. Coolant would get between the gasket and enter the combustion chamber. Also to anyone else who has done this. Did you use any kind of sealant on the gasket? I noticed the flimsy OEM one had no trace of sealant.


Modified by dballard at 6:11 PM 1/17/2008
dballard is offline   Reply With Quote
Old 01-17-2008, 06:04 PM   #2
 
reaper702's Avatar
 
Join Date: Jan 2007
Location: Las Vegas, Nevada, USA
Posts: 498
Default Re: Intake manifold torque specs? (dballard)

good question and i also would like to know as i just recently got my IMG in the mail today. btw, how long did it take to install?
reaper702 is offline   Reply With Quote
Old 01-17-2008, 06:18 PM   #3
Thread Starter
 
dballard's Avatar
 
Join Date: Oct 2007
Location: Edmeston, NY
Posts: 10
Default Re: Intake manifold torque specs? (reaper702)

I was taking my time so I used the DIY from 8thcivic. I removed the front brace which gave me MUCH more room to work. Taking my time it took about 2.5 hours. Biggest pain was actually removing the manifold after all the bolts were out. I didn't remove the two studs so the side of the manifold closest to the accessory belt would catch on a bracket. Just a little patience got it off. I'm still paranoid about coolant entering the manifold that I won't be able to see. I haven't seen where anyone uses sealant as of yet.
dballard is offline   Reply With Quote
Old 01-17-2008, 07:26 PM   #4
New User
 
fg2si!kid's Avatar
 
Join Date: May 2006
Location: ontario, cail, usa
Posts: 651
Default Re: Intake manifold torque specs? (dballard)

16 ft-lbs for the top nuts and the bottom bolts iam 100% sure i looked it up in my service manual
fg2si!kid is offline   Reply With Quote
Old 01-17-2008, 07:31 PM   #5
Thread Starter
 
dballard's Avatar
 
Join Date: Oct 2007
Location: Edmeston, NY
Posts: 10
Default Re: Intake manifold torque specs? (fg2si!kid)

You wouldn't happen to know the tightening sequence would you? Also, is it suggested to use any kind of gasket sealer in this installation?
dballard is offline   Reply With Quote
Old 01-17-2008, 07:37 PM   #6
New User
 
fg2si!kid's Avatar
 
Join Date: May 2006
Location: ontario, cail, usa
Posts: 651
Default Re: Intake manifold torque specs? (dballard)

"tighten the bolts and nuts in a crisscross pattern in three steps,beginning with the inner bolt" hahah is that good enough for you
fg2si!kid is offline   Reply With Quote
Old 01-17-2008, 07:40 PM   #7
New User
 
fg2si!kid's Avatar
 
Join Date: May 2006
Location: ontario, cail, usa
Posts: 651
Default Re: Intake manifold torque specs? (fg2si!kid)

oh and it does not say any thing about useing any kind of "honda bond" or sealer
fg2si!kid is offline   Reply With Quote
Old 01-18-2008, 07:32 AM   #8
Junior Member
 
hondamanforlife's Avatar
 
Join Date: Jan 2007
Location: pasadena, md, USA
Posts: 477
Default Re: Intake manifold torque specs? (fg2si!kid)

no sealant! no problem! I removed the top stud and replaced it with a bolt for future brake down so I would not need to mess with the idle pulley.
hondamanforlife is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Oil pan gasket! sealant or no? br8crumb Tech / Misc 11 09-14-2014 09:19 AM
Sealzall for carburetor gasket sealant? Richard123vmt Classic Hondas 0 10-20-2008 03:02 PM
when changing you oil pan gasket what do you use to clean the mating surfaces averyvm Honda Civic / Del Sol (1992 - 2000) 6 07-24-2008 11:36 PM
Installing a Header not sure TheAccordGuy Honda Prelude 4 06-27-2006 08:24 AM
silicone gasket sealant asianspeed Forced Induction 1 01-23-2003 09:09 PM


Tags
2003, accord, acura, element, honda, intake, mani, manifold, skunk2, spec, specifications, specs, tl, torque, wrx

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 03:58 PM.



Honda and the Honda marquee are registered trademarks of the American Honda Motor Company, Inc. Neither American Honda Motor Company nor its subsidiaries or affiliates shall bear any responsibility for Honda-Tech.com content, comments, or advertising. Honda-Tech.com is not affiliated with American Honda Motor Company in any way. American Honda Motor Company does not sponsor, support, or endorse Honda-Tech.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.