GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
#1
Who the fack changed my title?!
Thread Starter
GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
well, unfortunately my build has come to a very heart wrenching stop. it saddens me very dearly to do this but i must sell every part i have to pay off some big debts i have racked up in the past. this motor is fully built but it is not sleeved. i have mentioned everything EXCEPT the cams as in terms of price because they came with the head and i dont wanna charge for something that is not needed. this is a COMPLETE motor. when i say complete i mean all the way down to the last dam bolt and nut complete. the manifolds ARE included in this sale as well. everything i have listed below comes to roughly $8325.00 in parts and labor. if you have seen my build or if you have seen me around here on this web site, i do not take **** from any one but i wil dish it out when needed. i take my builds very seriously and it extremely hurts me to have to do this but it must be done. here listed below is a list of every part i have included in the sale with a price attached to it. some prices are reflecting the quality of the parts and some are not because i bought then used here goes.
srp pistons 489.95
eagle rods 350.00
balanced micropolished knife edged ls crank 125.00
gsr head 300.00
port and polish 900.00
bdl block guard 99.00
ls block obd1 with align honed main caps #3 main cap shaved down and gsr main girdle added in hot tanked bored and decked (81.5mm) 250.00
itr oil pump 80.00
gsr water pump 79.00
obd1 gsr distributor 110.00
bennen industries fuel rail 90.00
rc 1200cc injectors 300.00
edelbrock victor x manifold 265.00
edelbrock throttle plate spacer 50.00
top mount t3/t4 manifold for gsr only 310.00(wrapped with header wrap)
tial 44mm waste gate with 20 psi spring 350.00
7 or 8 inch elbow for waste gate 75.00
block fittings for catch can 65.00
-10 an fittings for block fittings 45.00
billet cam seal 35.00
type r oil cooler 65.00
fluidampr 250.00
gates racing belt 100.00
toda cam gears 300.00
type r dual valve springs and retainers 100.00
supertec black nitrade valves 259.00
golden eagle head gasket 81.5mm 114.99
valve cover gasket 20.00
oil pan gasket 27.00
ngk slugs with a step colder ~35.00
intermediate shaft 55.00
oil orifice gasket set 10.00
valve stem seals 35.00
gsr valve cover with -10an swivel fittings welded on(tig) 125.00
omni power map sensor 108.00
ls vtec dowel pin set 25.00
ls vtec kit(line allen plug and t fitting) 45.00
sandwhich plate 29.00
.20 over bearings 135.00
morosso oil pan 385.00
arp head stud and main cap kit 175.00
matching oil pick up for morosso oil pan 56.00
exedy twin disk clutch 750.00 plates have been used
gsr transmission new carbon synchros, new 3rd sleeve, new bearings, seals, ball bearings, throwout bearing/pilot, painted casing, new seals on countershaft side(in between 1st & 2nd) 750.00
THIS IS FOR SERIOUS BUYERS ONLY. dont fvck with me if you are not serious. buyer is responsible for transportation and shipping. please pm me with any questions or concerns you can also get in touch with me at 832-235-0057. please do not waste my time and i will certainly not waste yours. thanks!
-zack
srp pistons 489.95
eagle rods 350.00
balanced micropolished knife edged ls crank 125.00
gsr head 300.00
port and polish 900.00
bdl block guard 99.00
ls block obd1 with align honed main caps #3 main cap shaved down and gsr main girdle added in hot tanked bored and decked (81.5mm) 250.00
itr oil pump 80.00
gsr water pump 79.00
obd1 gsr distributor 110.00
bennen industries fuel rail 90.00
rc 1200cc injectors 300.00
edelbrock victor x manifold 265.00
edelbrock throttle plate spacer 50.00
top mount t3/t4 manifold for gsr only 310.00(wrapped with header wrap)
tial 44mm waste gate with 20 psi spring 350.00
7 or 8 inch elbow for waste gate 75.00
block fittings for catch can 65.00
-10 an fittings for block fittings 45.00
billet cam seal 35.00
type r oil cooler 65.00
fluidampr 250.00
gates racing belt 100.00
toda cam gears 300.00
type r dual valve springs and retainers 100.00
supertec black nitrade valves 259.00
golden eagle head gasket 81.5mm 114.99
valve cover gasket 20.00
oil pan gasket 27.00
ngk slugs with a step colder ~35.00
intermediate shaft 55.00
oil orifice gasket set 10.00
valve stem seals 35.00
gsr valve cover with -10an swivel fittings welded on(tig) 125.00
omni power map sensor 108.00
ls vtec dowel pin set 25.00
ls vtec kit(line allen plug and t fitting) 45.00
sandwhich plate 29.00
.20 over bearings 135.00
morosso oil pan 385.00
arp head stud and main cap kit 175.00
matching oil pick up for morosso oil pan 56.00
exedy twin disk clutch 750.00 plates have been used
gsr transmission new carbon synchros, new 3rd sleeve, new bearings, seals, ball bearings, throwout bearing/pilot, painted casing, new seals on countershaft side(in between 1st & 2nd) 750.00
THIS IS FOR SERIOUS BUYERS ONLY. dont fvck with me if you are not serious. buyer is responsible for transportation and shipping. please pm me with any questions or concerns you can also get in touch with me at 832-235-0057. please do not waste my time and i will certainly not waste yours. thanks!
-zack
Last edited by sh!ft; 10-17-2011 at 09:42 AM.
#2
Who the fack changed my title?!
Thread Starter
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
up. the price i posted was not what i was looking for. i AM trying to get something close to that price.
#6
Honda-Tech Member
Join Date: Nov 2010
Location: kansas city mo
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
interested in selling the t3/4 manifold seperate? if so what brand call or text anytime 816-606-9719 thanks and if not free bump for you!
Trending Topics
#9
Who the fack changed my title?!
Thread Starter
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
up. lots of interest. i will not part out UNLESS i have buyers for everything. so there is some food for thought.
#13
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
Hey im very interested in the ls crank i have an ls-v turbo with a spun bearing and need a new crank. Is it still for sale, where are you located, and can u ship? Im in new jersey
Thanks,
Dan
Thanks,
Dan
#14
Who the fack changed my title?!
Thread Starter
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
you are the 2nd person to ask about the crank. i am waiting till i can get enough people to purchase a few more things then i will part out. i do not want to part out one thing and rip apart the motor just to sell one thing. if i rip apart the motor i want to have most of the items spoken for. ill keep you posted.
#17
Honda-Tech Member
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
k this might be a dumb ? but y will that turbo mani only fit a gsr, cuz i have a ls/v in a ef
#19
Who the fack changed my title?!
Thread Starter
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
not that, the gsr had different intake bolt patterns than all the other motors.
#20
Honda-Tech Member
Join Date: Feb 2008
Location: central valley
Posts: 2,160
Likes: 0
Received 0 Likes
on
0 Posts
Re: GAUGING INTEREST!!! BUILT LSVTEC LONG BLOCK AND TRANSMISSION
he said turbo manifold some im guessing its the exhaust
which all exhuast manifolds have the same bolt patterns for b series
which all exhuast manifolds have the same bolt patterns for b series
Thread
Thread Starter
Forum
Replies
Last Post
_HANS
Mid-Atlantic (Sales)
0
07-02-2006 12:30 PM