High(er) compression vs Boost?
#1
High(er) compression vs Boost?
I know the classic ideal is low compression for boost, high compression for n/a.
BUT if one wanted to run higher compression, logically the lower the boost you run the higher the compression you could run safely. Ideally, the higher compression would benefit you when not in boost but the low boost level would keep this safe.
My question is, on a given setup...
b20
pistons
rods
blockguard
hondata
8lbs daily - 10lbs max
What would be the safest compression you could run?
9.5:1?
10:1?
BUT if one wanted to run higher compression, logically the lower the boost you run the higher the compression you could run safely. Ideally, the higher compression would benefit you when not in boost but the low boost level would keep this safe.
My question is, on a given setup...
b20
pistons
rods
blockguard
hondata
8lbs daily - 10lbs max
What would be the safest compression you could run?
9.5:1?
10:1?
#2
Guest
Posts: n/a
#3
Honda-Tech Member
Re: High(er) compression vs Boost? (thinkbrianthink)
The lower the compression, the safer it would be. Ceteris paribus
I once had this idea, I think it would be a killer setup for the street.
built B16A
10:1 pistons
smaller turbo, say a T3
medium boost (~11psi)
4.745:1 or 4.9:1 FD ratio
LSD
*shrugs shoulders*
I once had this idea, I think it would be a killer setup for the street.
built B16A
10:1 pistons
smaller turbo, say a T3
medium boost (~11psi)
4.745:1 or 4.9:1 FD ratio
LSD
*shrugs shoulders*
#4
Honda-Tech Member
Re: High(er) compression vs Boost? (xThexHeadx)
The lower the compression, the safer it would be. Ceteris paribus
I once had this idea, I think it would be a killer setup for the street.
built B16A
10:1 pistons
smaller turbo, say a T3
medium boost (~11psi)
4.745:1 or 4.9:1 FD ratio
LSD
*shrugs shoulders*
I once had this idea, I think it would be a killer setup for the street.
built B16A
10:1 pistons
smaller turbo, say a T3
medium boost (~11psi)
4.745:1 or 4.9:1 FD ratio
LSD
*shrugs shoulders*
All that needs is a hobbs controled water/alch injection
EDIT:
QuickHonda runs a 10:1 CR in his ZC. Runs 14psi on his Drag3 kit on pump gas. High boost and high CR CAN Be done safely. It is a FACT.
[Modified by Bryson, 1:35 PM 10/11/2002]
#5
Re: High(er) compression vs Boost? (filetofit)
Good info in the link... If you can understand it (i did... kinda)
I understand the fact that your talking about two different compression factors in this case and that raising engine compression will not necessarily raise your peak horsepower. What im aiming for is more "oomph" in the low end as a result of higher compression but also keeping it safe at 10lbs on the high end.
[Modified by thinkbrianthink, 2:46 PM 10/11/2002]
I understand the fact that your talking about two different compression factors in this case and that raising engine compression will not necessarily raise your peak horsepower. What im aiming for is more "oomph" in the low end as a result of higher compression but also keeping it safe at 10lbs on the high end.
[Modified by thinkbrianthink, 2:46 PM 10/11/2002]
#7
Honda-Tech Member
Re: High(er) compression vs Boost? (Bryson)
The lower the compression, the safer it would be. Ceteris paribus
QuickHonda runs a 10:1 CR in his ZC. Runs 14psi on his Drag3 kit on pump gas. High boost and high CR CAN Be done safely. It is a FACT.
[Modified by Bryson, 1:35 PM 10/11/2002]
QuickHonda runs a 10:1 CR in his ZC. Runs 14psi on his Drag3 kit on pump gas. High boost and high CR CAN Be done safely. It is a FACT.
[Modified by Bryson, 1:35 PM 10/11/2002]
I think that one thing enthusiasts need to understand, is that wehn we are talking about high compression...we're talking 12.5:1, etc...STOCK Honda compression, really isn't that high afterall...Not even close to being high enough to cause such catastrophic failures that all of the low comp guys are always talking about.
Trending Topics
#9
Re: High(er) compression vs Boost? (MatT3T4)
Good info.
This is the type of responses i was looking for. You always hear of ppl saying 8.5:1 and 9:1 but then these figures are also mentioned full race setups. I figured there had to be a happy medium for a small boost application.
Thanks guys,
brian
-tech.com
[Modified by thinkbrianthink, 3:19 PM 10/11/2002]
This is the type of responses i was looking for. You always hear of ppl saying 8.5:1 and 9:1 but then these figures are also mentioned full race setups. I figured there had to be a happy medium for a small boost application.
Thanks guys,
brian
-tech.com
[Modified by thinkbrianthink, 3:19 PM 10/11/2002]
#10
Guest
Posts: n/a
Re: High(er) compression vs Boost? (MatT3T4)
Higher engine compression will raise the temperature of the compressed air/fuel mixture by definition. Higher temperature mixtures put you closer to the spontaneous ignition point ( =detonation, bad) all other things being equal like octane, timing etc. But if you can get away with higher compression at the boost level you want to run with pump gas and not too much timing retard, hell more power to ya. It just means your closer to the edge that's all. All together now, tuuuuning.
#11
Honda-Tech Member
Re: High(er) compression vs Boost? (filetofit)
Higher engine compression will raise the temperature of the compressed air/fuel mixture by definition. Higher temperature mixtures put you closer to the spontaneous ignition point ( =detonation, bad) all other things being equal like octane, timing etc. But if you can get away with higher compression at the boost level you want to run with pump gas and not too much timing retard, hell more power to ya. It just means your closer to the edge that's all. All together now, tuuuuning.
I like your style.
I guess what a lot of people don't understand is that, for a STREET application, the stock compression in the B-series motors is fine. Even in the R motors it's alright (kinda pushing it, but still alright...if it wasn't for the lightweight internals).
#12
Join Date: Oct 2002
Location: Holland, below sealevel....., Holland
Posts: 99
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (MatT3T4)
Also planning on building b16a1 for street. 10:1 and bout 14psi. In Europe we have 98 octane.............
What tuning should you guys advise? Already running 6psi GReddy kit, lost blue box, Vortech FMU, Bosch inline 220lph.
What tuning should you guys advise? Already running 6psi GReddy kit, lost blue box, Vortech FMU, Bosch inline 220lph.
#13
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (MatT3T4)
"It's all in the tuning".. I hate that phrase..
Uh huh... Well on pump gas .. you have to run so much timing retard to avoid detonation that there is an obvious point of diminishing return in running high boost.
Read this, these people know what they are talking about:
http://www.sdsefi.com/meltdown.htm
On 91 octane, with 10:1 compression you can run about 10psi at most before the thing pings. Then you get to pull so much timing that you start losing power per extra pound of boost..
Uh huh... Well on pump gas .. you have to run so much timing retard to avoid detonation that there is an obvious point of diminishing return in running high boost.
Read this, these people know what they are talking about:
http://www.sdsefi.com/meltdown.htm
On 91 octane, with 10:1 compression you can run about 10psi at most before the thing pings. Then you get to pull so much timing that you start losing power per extra pound of boost..
#14
Honda-Tech Member
Re: High(er) compression vs Boost? (dustin)
"It's all in the tuning".. I hate that phrase..
Uh huh... Well on pump gas .. you have to run so much timing retard to avoid detonation that there is an obvious point of diminishing return in running high boost.
Read this, these people know what they are talking about:
http://www.sdsefi.com/meltdown.htm
Uh huh... Well on pump gas .. you have to run so much timing retard to avoid detonation that there is an obvious point of diminishing return in running high boost.
Read this, these people know what they are talking about:
http://www.sdsefi.com/meltdown.htm
Stock B-series compression...anywhere from 9.2:1-10.6:1 or so...is not high. We are talking about street cars here. That amount of static compression does not warrant extreme timing retard, and 116 octane fuel. I think that some people confuse HIGH compression for stock compression. When hundreds of enthusiasts can easily and successfully boost their motors, and have it last a long time, with no problems...on stock compression, what is the problem?
You know where the point of diminishing returns becomes a problem? It becomes a problem when you are making so much power, you can't keep traction. That is why I don't see the purpose of building a street car. You WILL reach the point of diminishing returns with stock compression, safely...so why spend $4,000 just so you can lower your compression, and hit that threshhold anyway?
It works well both ways, don't get me wrong...lowering compression makes sense and it a feasable option, but on a race car. It doesn't make too much sense on a car that can't reap the benefits of being able to boost 69864599psi on a 7.0:1 motor...on the street.
#15
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (dustin)
Here is another good link from people that actually know about engines
http://www.sdsefi.com/techocta.htm
http://www.sdsefi.com/techocta.htm
#16
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (MatT3T4)
Ok, here is what I don't understand.
Stock B-series compression...anywhere from 9.2:1-10.6:1 or so...is not high. We are talking about street cars here. That amount of static compression does not warrant extreme timing retard, and 116 octane fuel. I think that some people confuse HIGH compression for stock compression.
Stock B-series compression...anywhere from 9.2:1-10.6:1 or so...is not high. We are talking about street cars here. That amount of static compression does not warrant extreme timing retard, and 116 octane fuel. I think that some people confuse HIGH compression for stock compression.
When hundreds of enthusiasts can easily and successfully boost their motors, and have it last a long time, with no problems...on stock compression, what is the problem?
You know where the point of diminishing returns becomes a problem? It becomes a problem when you are making so much power, you can't keep traction. That is why I don't see the purpose of building a street car. You WILL reach the point of diminishing returns with stock compression, safely...so why spend $4,000 just so you can lower your compression, and hit that threshhold anyway?
It works well both ways, don't get me wrong...lowering compression makes sense and it a feasable option, but on a race car. It doesn't make too much sense on a car that can't reap the benefits of being able to boost 69864599psi on a 7.0:1 motor...on the street.
#17
New User
Join Date: Dec 2000
Location: Houston, TX, usa
Posts: 370
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (ee8T)
My new motor is 11.4:1 with 25psi.. I wouldn't try to run high without standalone though, you need a way to acurately control timing and fuel..
#18
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (brian b)
My new motor is 11.4:1 with 25psi.. I wouldn't try to run high without standalone though, you need a way to acurately control timing and fuel..
#19
Honda-Tech Member
Re: High(er) compression vs Boost? (dustin)
Here is another good link from people that actually know about engines
They're talking about a hypothetical engine, I can make a hypothetical engine look like anything. I'm not disagreeing with you, but I am saying that all of this whoopla about things being so dangerous with their stock motor is just that...whoopla. Unless you've actually done it numerous times, you won't know it. We're talking about street cars here, race cars are a different story.
There are a lot of factors that come into play: weather conditions, driving conditions, octane, timing, etc...In NORMAL street conditions, the average enthusiast knows what he is doing, and on a stock motor, isn't endangering himself too much. It's like a mass hysteria that I just don't understand.
Maybe I am special though, because I can run for 2 years on a stock B16A boosting 10-17psi revving up to 9,000rpm. Well, myself, and all of the other cars I had my hand in building. I am blessed.
#20
Honda-Tech Member
Re: High(er) compression vs Boost? (dustin)
Ok, here is what I don't understand.
They do not last a long time. Look how many people here crack ring lands. You can't run high boost (>10psi) with reasonable ignition advance on pump gas RELIABLY with 10:1 compression. It might work now. It might work for a friend. It might work for a guy in your 'krew'. It might work for this guy you know that talked to this other guy who has this really sweet *** car. But it's not going to work forever -- You will break something.
They do not last a long time. Look how many people here crack ring lands. You can't run high boost (>10psi) with reasonable ignition advance on pump gas RELIABLY with 10:1 compression. It might work now. It might work for a friend. It might work for a guy in your 'krew'. It might work for this guy you know that talked to this other guy who has this really sweet *** car. But it's not going to work forever -- You will break something.
Replace a built motor: $4,000
Replace a stock motor: $400
#21
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (MatT3T4)
Hey mat, a google search with your username revealed this
http://www.hondalife.com/effectivecompression.htm
I think you wrote that, or someone who stole your name did...
Your argument is that adding boost to yield higher dynamic compression will not make more power than the motor that started with higher static compression...
But, understand, that the power output of an engine is directly related to its ability to burn FUEL. When you add boost, you get to add fuel! Increasing static compression ratio sure does increase peak cylinder pressure... But burning more fuel yields more area under the "cylinder pressure curve"!
Bottom line.. the engine that burns more fuel is gonna win.
http://www.hondalife.com/effectivecompression.htm
I think you wrote that, or someone who stole your name did...
Your argument is that adding boost to yield higher dynamic compression will not make more power than the motor that started with higher static compression...
But, understand, that the power output of an engine is directly related to its ability to burn FUEL. When you add boost, you get to add fuel! Increasing static compression ratio sure does increase peak cylinder pressure... But burning more fuel yields more area under the "cylinder pressure curve"!
Bottom line.. the engine that burns more fuel is gonna win.
#22
What is this crap?
Re: High(er) compression vs Boost? (dustin)
My new motor is 11.4:1 with 25psi.. I wouldn't try to run high without standalone though, you need a way to acurately control timing and fuel..
And lots of race gas
And lots of race gas
edit - this post is a joke. just so you know. ha ha. you're not laughing. nevermind.
#23
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: High(er) compression vs Boost? (MatT3T4)
They're talking about a hypothetical engine, I can make a hypothetical engine look like anything. I'm not disagreeing with you, but I am saying that all of this whoopla about things being so dangerous with their stock motor is just that...whoopla. Unless you've actually done it numerous times, you won't know it. We're talking about street cars here, race cars are a different story.
There are a lot of factors that come into play: weather conditions, driving conditions, octane, timing, etc...In NORMAL street conditions, the average enthusiast knows what he is doing, and on a stock motor, isn't endangering himself too much. It's like a mass hysteria that I just don't understand.
Maybe I am special though, because I can run for 2 years on a stock B16A boosting 10-17psi revving up to 9,000rpm. Well, myself, and all of the other cars I had my hand in building. I am blessed.
There are a lot of factors that come into play: weather conditions, driving conditions, octane, timing, etc...In NORMAL street conditions, the average enthusiast knows what he is doing, and on a stock motor, isn't endangering himself too much. It's like a mass hysteria that I just don't understand.
Maybe I am special though, because I can run for 2 years on a stock B16A boosting 10-17psi revving up to 9,000rpm. Well, myself, and all of the other cars I had my hand in building. I am blessed.
#24
Honda-Tech Member
Re: High(er) compression vs Boost? (dustin)
Hey mat, a google search with your username revealed this
http://www.hondalife.com/effectivecompression.htm
I think you wrote that, or someone who stole your name did...
Your argument is that adding boost to yield higher dynamic compression will not make more power than the motor that started with higher static compression...
But, understand, that the power output of an engine is directly related to its ability to burn FUEL. When you add boost, you get to add fuel! Increasing static compression ratio sure does increase peak cylinder pressure... But burning more fuel yields more area under the "cylinder pressure curve"!
Bottom line.. the engine that burns more fuel is gonna win.
http://www.hondalife.com/effectivecompression.htm
I think you wrote that, or someone who stole your name did...
Your argument is that adding boost to yield higher dynamic compression will not make more power than the motor that started with higher static compression...
But, understand, that the power output of an engine is directly related to its ability to burn FUEL. When you add boost, you get to add fuel! Increasing static compression ratio sure does increase peak cylinder pressure... But burning more fuel yields more area under the "cylinder pressure curve"!
Bottom line.. the engine that burns more fuel is gonna win.
#25
Honda-Tech Member
Re: High(er) compression vs Boost? (dustin)
This sounds like a cop out argument to avoid the laws of physics and thermodynamics...