1990 Honda CRX HF Project Lots of pics
#126
Honda-Tech Member
Thread Starter
Join Date: Sep 2004
Location: Some where in, WA, USA
Posts: 1,610
Likes: 0
Received 1 Like
on
1 Post
hah, didnt rattle can it. We painted it another way. But we arent done painting it.
I just bought an Exedy Lightened Flywheel 9.5 lbs. for 210 bucks.
It was the best I could find it for. So I got it. Once I get my pistons and the flywheel I will have the machine shop balance the rotating assembly.
I just bought an Exedy Lightened Flywheel 9.5 lbs. for 210 bucks.
It was the best I could find it for. So I got it. Once I get my pistons and the flywheel I will have the machine shop balance the rotating assembly.
#127
Honda-Tech Member
Thread Starter
Join Date: Sep 2004
Location: Some where in, WA, USA
Posts: 1,610
Likes: 0
Received 1 Like
on
1 Post
Re: (jakscivic)
So the brown santa came today!!! I got my P30 pistons. Finally I can take them over to the machine shop and have them finish my block!
Thank you http://www.hmotorsonline.com
Thank you http://www.hmotorsonline.com
#128
Honda-Tech Member
Thread Starter
Join Date: Sep 2004
Location: Some where in, WA, USA
Posts: 1,610
Likes: 0
Received 1 Like
on
1 Post
Ok, so I took the pistons down to the machine shop and guess what? They needed to machine the block more! So now instead of it being .25 over, its going to be .50 over. So now I need to buy NEW pistons AGAIN.
I will be going through RS Machine and getting a set of ITR pistons. So that means I need to get the rods machined to match the piston heads and while they are doing that I am going to get them to retang the rods to fit the GSR bearings.
I will be going through RS Machine and getting a set of ITR pistons. So that means I need to get the rods machined to match the piston heads and while they are doing that I am going to get them to retang the rods to fit the GSR bearings.
#129
Honda-Tech Member
Thread Starter
Join Date: Sep 2004
Location: Some where in, WA, USA
Posts: 1,610
Likes: 0
Received 1 Like
on
1 Post
Ok, so more presents today. I got the pr3 piston rings! Which are now completly useless! So I will be selling the .25os p30 pistons along with the rings here shortly.
Also got the windshield washer fluid spray nozels. Since I broke my other ones trying to get them out of the hood.
Also got the windshield washer fluid spray nozels. Since I broke my other ones trying to get them out of the hood.
#130
Honda-Tech Member
Thread Starter
Join Date: Sep 2004
Location: Some where in, WA, USA
Posts: 1,610
Likes: 0
Received 1 Like
on
1 Post
Re: (jakscivic)
This will be my set up for LSVTEC. Of course it may change a little. But I pretty much have all the parts.
Head:
B16a Head
GSR cams
Stock valve train
GSR ARP head studs
OEM honda head gasket
Skunk2 Intake Manifold
Hondata Intake manifold gasket
Cold air intake
Exhaust:
Hytech Replica header
Replica Mugen Twin loop muffler from SNL
2.5" exhaust with mandrel bent pipeing
GE LSVTEC conversion kit
Block:
B18b Block
.50 OS
Shot peened ls rods
ARP rod bolts
ARP Main bolts
GSR Rod bearings
RSX Type S Main bearings
RS Machine ITR pistons .50 os
ITR oil pump
B16a water pump
Moroso Oil pan
Tranny:
Y1 cabel tranny
ACT stage 1 clutch
Exedy 9.5 lb flywheel
B&M Short shifter
Machine work Im getting done:
Polished crank
Retanged rods to fit GSR bearings
Machined rods to fit ITR pistons
Decked block
Honed cylinder walls
Tuning/ECU:
Rywire Obd0-Obd1 conversion
Hondata S200
Hope to get it tuned by intec
Head:
B16a Head
GSR cams
Stock valve train
GSR ARP head studs
OEM honda head gasket
Skunk2 Intake Manifold
Hondata Intake manifold gasket
Cold air intake
Exhaust:
Hytech Replica header
Replica Mugen Twin loop muffler from SNL
2.5" exhaust with mandrel bent pipeing
GE LSVTEC conversion kit
Block:
B18b Block
.50 OS
Shot peened ls rods
ARP rod bolts
ARP Main bolts
GSR Rod bearings
RSX Type S Main bearings
RS Machine ITR pistons .50 os
ITR oil pump
B16a water pump
Moroso Oil pan
Tranny:
Y1 cabel tranny
ACT stage 1 clutch
Exedy 9.5 lb flywheel
B&M Short shifter
Machine work Im getting done:
Polished crank
Retanged rods to fit GSR bearings
Machined rods to fit ITR pistons
Decked block
Honed cylinder walls
Tuning/ECU:
Rywire Obd0-Obd1 conversion
Hondata S200
Hope to get it tuned by intec
#132
Honda-Tech Member
Thread Starter
Join Date: Sep 2004
Location: Some where in, WA, USA
Posts: 1,610
Likes: 0
Received 1 Like
on
1 Post
Its been really slow going between school and work. But I bought Innovative mounts and some new bearings. I just need to have the pistons put on the rods.
After that its all set to go. I should be buying Hondata s300 here soon. My plan is to Have the engine all put in and running by the end of this month. That is if my boss isnt a ***** and gives me the time off.
After that its all set to go. I should be buying Hondata s300 here soon. My plan is to Have the engine all put in and running by the end of this month. That is if my boss isnt a ***** and gives me the time off.
#133
Honda-Tech Member
Join Date: Mar 2007
Location: DeLand, Florida, North America
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
Re: 1990 Honda CRX HF Project Lots of pics (jakscivic)
Yo Where Did You Get The Wrinkle Finish Paint For The Valve Cover And What Kinda?
It Looks Clean As [freak] BUMP!!!
It Looks Clean As [freak] BUMP!!!
Thread
Thread Starter
Forum
Replies
Last Post
FSTVTEC
Appearance Build Threads
37
03-22-2009 06:24 AM