B18civic5g

I have a 92 cx hatch back, with a JDM SIR-g motor. i want ideas for what cams i should use?
MODS
ACT FLYWHEEL
EXEDY CLUTCH
SKUNK2 INTAKE MANIFOLD
SHORT RAM 3" INTAKE
JDM ITR HEADER
RSR "B" PIPE ONLY FOR NOW
hondata S200

HERE IS MY DYNO RIGHT NOW



AND A LINK TO MY CAR

https://honda-tech.com/zerothread?id=1074927


THANKS FOR THE HELP , AND I DID DO A SEARCH FIRST


Modified by B16civic4g at 4:42 PM 12/12/2004


Modified by B16civic4g at 4:43 PM 12/12/2004

B18civic5g

bump i want to but cams

B18civic5g

some ideas please

drdisco69

CTR cams can be had for cheap and make good power while being OEM reliable.

B18civic5g

i do not think that i will gan that much from ctr cams, i was thinking about shunk2 stage2's , buddy club spec3's

drdisco69

You will gain from those cams, but from what I have read, they really work best with higher compression, like over 11.5:1. I'd like to hear from other people though, I'm shopping as well, although I'm pretty sure I'm getting CTRs.

B18civic5g

i would also like to hear what other people have in mind too.

revvin9k

Got Skunk2 Stage 2s in my b18c-r , put down 195hp 126tq with a stock ecu, stock JDM pistons.

B18civic5g

thanks,,,,,,,,,,, more people must have cams?

B18civic5g

bump

B18civic5g

bump

B18civic5g

up to the top

B18civic5g

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by B16civic4g &raquo;</TD></TR><TR><TD CLASS="quote">up to the top </TD></TR></TABLE>

i 4

what about some BC III cams

B18civic5g

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by i 4 &raquo;</TD></TR><TR><TD CLASS="quote">what about some BC III cams</TD></TR></TABLE>

i have been doing alot of searching on these cams , i think i want these but i want ideas of somelse ?


thanks

99 TYPE R

yo kid nice dyno # to bad they r not urs this dyno chart was done with a gsr motor and a jdm race header for 150.00 guys the post in the type r forum, and a s2 manifoldand a few other thing, damn kids its so easy to copy and paste

estonia is for lovers

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 99 TYPE R &raquo;</TD></TR><TR><TD CLASS="quote">yo kid nice dyno # to bad they r not urs this dyno chart was done with a gsr motor and a jdm race header for 150.00 guys the post in the type r forum, and a s2 manifoldand a few other thing, damn kids its so easy to copy and paste</TD></TR></TABLE>

i was about to say the same thing..no way that b16 with bolt ons got over 180 whp, haha go with skunk 2's stage 2's

B18civic5g

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by efniner91 &raquo;</TD></TR><TR><TD CLASS="quote">

i was about to say the same thing..no way that b16 with bolt ons got over 180 whp, haha go with skunk 2's stage 2's</TD></TR></TABLE><TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 99 TYPE R &raquo;</TD></TR><TR><TD CLASS="quote">yo kid nice dyno # to bad they r not urs this dyno chart was done with a gsr motor and a jdm race header for 150.00 guys the post in the type r forum, and a s2 manifoldand a few other thing, damn kids its so easy to copy and paste</TD></TR></TABLE>

if for one fuckn min. you think i copyed and pasted this ,,,


**** YOU READ THIS THREAD


https://honda-tech.com/zerothread?id=1074927


THIS IS MY CAR......... AND I HAVE S200 HONDATA BITCH

estonia is for lovers

soo you have 2 screen names?

B18civic5g

no!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

608 Gangsta

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 99 TYPE R &raquo;</TD></TR><TR><TD CLASS="quote">yo kid nice dyno # to bad they r not urs this dyno chart was done with a gsr motor and a jdm race header for 150.00 guys the post in the type r forum, and a s2 manifoldand a few other thing, damn kids its so easy to copy and paste</TD></TR></TABLE>

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by efniner91 &raquo;</TD></TR><TR><TD CLASS="quote">

i was about to say the same thing..no way that b16 with bolt ons got over 180 whp, haha go with skunk 2's stage 2's</TD></TR></TABLE>

sorry to bust ur bubble but.. hes a friend of mine and i was there when he dynoed and when he got the sheet and when he copied it onto the computer.. so sorry and its not a ****** b16 dumbass..if u all dont think its possible mabey your having the wrong people tune ur ****.. they prolly dont know what there doing.. sorry

Go Dynotuned

LSVTEC 91 Civic

B18civic5g

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by LsFrnknstn &raquo;</TD></TR><TR><TD CLASS="quote">

sorry to bust ur bubble but.. hes a friend of mine and i was there when he dynoed and when he got the sheet and when he copied it onto the computer.. so sorry and its not a ****** b16 dumbass..if u all dont think its possible mabey your having the wrong people tune ur ****.. they prolly dont know what there doing.. sorry

Go Dynotuned </TD></TR></TABLE>


thank you sam

ek9800

i got skunk2 stage2 and i love them

scLSteg

I've just dynoed a pair of BCIII+ cams in my JDM Sir-G . . .
thread name in ALL MOTOR is 200whp stock block gsr or something
posted pic of dyno though its kinda of rough but you'll get an idea . .