thegr8one013

FS

Mfactory 3.070 1st gear meant for those with a 4.7 final drive.



$200

located in inwood, ny 11096
516-330-6190

snm95ls

Golden Eagle Manufacturing sandwich plate kit for LS-VTEC

120 shipped.

my9thtry

i have everything for sale out of my 95 prelude. Motor was put together by DFE tuned by Phearable ran for 1700 miles. Between deployments and work i just dont have time anymore and want to move these parts.

Block $999
H23a Block factory all B block bored 87.25mm
Oil Squirters have been removed, Oil galleys in the block have been re- prioritized to better suit a high revving N/A H22 and the H22 windage plates are being used (custom DFE assembly procedure)
Mahle Gold Pistons (11.5 to 1)
Eagle Rods (New style with bigger rods bolts)
Fresh H22a1 Crankshaft
ACL Race bearings
Lightened Factory Crank Pulley (Milled off the PS ribs and re balanced)
New OEM Oil, Water Pumps, and Gasket Kit
OEM Alternator and Bracket
H22 Power Steering Bracket
H22 Water Line and Thermostat Housing
All Sensors included except knock sensor.

Head $1200
H22 Head, fresh guides, valve job and mild port work
Skunk 2 Pro 2 Cams, Adjustable gears, and Valves
Supertech Springs and Retainers
OEM H22 Valve cover has been tapped with -10 lines
B&R Fittings catch can kit
VTEC Solenoid and brand new USDM Distributor are included (Distributor King).
NGK Plug wires

Wheels and Tires
OEM “Si” Wheels fresh bead blast and coat of paint $200
BRAND NEW 5zigen ZX-6 in 16x7 +42 with 215/45/16 Hankook RS-2 $650

Euro R Intake Manifold $450
Ports have been reshaped by Rosko to fit the US spec head and TB Bored to 69mm
All of the EGR system has been removed (This was over 16 hours of work with a die grinder, then welded the ports shut and ground flush both internally and externally then painted wrinkle black)
DH Racing Billet 74-69mm TB
Thermoplastic IM Gasket
Rosko Racing
Fuel Rail Adapter
IACV Adapter
Throttle Cable Bracket
Port work and tapped fittings
All Sensors included. ready to bolt on.

BPi Flow Stack with Filter $40

VTEC Calipers and Rotors $75
Hawk HPS pads with 20 miles $90
Goodrich SS brake Lines $85

Progess 27mm rear Sway Bar $180

Auto to Manual Swap $650
Explicit Speed Performance Automatic to Manual Mount Kit
Forbidden Motorsports Short Shifter
5 Speed Shifter Assembly, Cables, Clutch Master Cylinder with Earls Braided line Resivor Pedal Assembly and Manual Brake Pedal
Axles and halfshaft
Rear engine mount bracket, yes its different on manual cars.
Starter

209lsr_ly

iTrader: (1)

FS

B16b short block
RS sleeves
85mmx89mm with arais 14:1 pistons
acl race bearings
eagle rods w/ arp big bolts
blocks has 6 runs only and 8 dyno pulls

block is still in a running car/chassis
on e85 making 271whp (look at signature)

asking 1800 obo (price is negotiable)

proFab 421 (not replica) b series header
used with block above
asking 350 + shipping n fees

95mm eagle crank shaft
asking 350 obo + shipping n fees

aeromotive A1000 (the red one) fuel pump
asking 150

pm for pictures

slowsleeper

I am looking to sell my set of used Carrillo Pro A LS Connecting Rods that i was running in my engine, they are light as hell for a steel rod weighing in at 421 grams each. Probably one of the top of the line rods that are decently affordable. The rods are tanged for GSR bearings btw but either set (LS/GSR) will work. Looking to get 590 shipped for the set.




When the rods were brand new


I also have a set of brand new in box Wiseco 86mm B-series custom pistons complete with wrist pins, clips, and rings.

They are 5.5cc dome, skirt coating, and comes with spec sheet etc. I found out I'm having to go with a bigger bore in order to use my block so that is the only reason for selling. Looking to get 520 shipped







More pics available if needed. Like I said, they are brand new.

Mugen Type R

Wtb smsp b18 or b19 header

howl

iTrader: (3)

Location: So. Cal

I have Avid Racing solid pro-billet EG/DC b-series motor mounts for sale. Bought this from another member but never used it. $300 shipped.

Would trade for ITR parts plus cash (depending on item): door panels, front/rear strut bar, mugen rear sway bar, USDM '98 ecu

PM or text at 909-529-6833.

DSDoneJimmy

WTT 24.5x13 m&h slicks for 22 or 23 x 13 inch slicks. My tires have about 5 passes on them wanting to trade in something in the same condition preferably in the Sacramento area. Thanks

EH3forlife

FS: Ported P8R Head, Has brian crower valve springs with crower steel retainers. Item is on ebay:

http://www.ebay.com/itm/110940482912

jordanprince

Fully Built LSvtec 86x92 250+ whp swap 150 miles on the swap for sale

RS 900hp sleeved LS bock
Endyn 14.5:1 stroker pistons
Eagle Rods
92mm stroker crank

$1300 for the shortblock

Built B16 head has full valvetrain - 450
Edelbrock victorX IM - 200
RMF rep Headers mit condition - 200
skunk2 pro 2 cams with adjustable cam gears - 450
B16 tranny with Lsd - 450

pm me

Andy@AMR

New Skunk2 Pro1 Series Cams. Installed, but never ran. Too much cam for me. ZERO miles. 550 shipped.

Skunk2 Pro-Series Front Camber Kit EK. This was installed, but never ran on the street. They are pretty much new, like the cams. Boots are perfect. 155 shipped.












Trades considered are chipped P28, Neptune RTP, AEM Boost Gauge, AEM Oil Pressure Gauge, 1999-2000 Civic Rear Left Inner Tail lights, and Right Outter Tail Light, 99-00 Civic Passenger Headlight, CTR EK9 Cup Holde, Hondata S300..+cash depending on what you all got.

artie89

iTrader: (4)

PLM Style B Series Narrow Header -150