best cams and headers for me??
#1
best cams and headers for me??
My setup
B18c block
Ls crank
Ls rods
Usdm type r pistons
B16 head
Type r manifold w/ 70mm tb
port n polished
3 angle valve job
Rocket spring and titanium retainers
Gsr tranny
Arp rod bolts and head bolts
Any suggestions??
B18c block
Ls crank
Ls rods
Usdm type r pistons
B16 head
Type r manifold w/ 70mm tb
port n polished
3 angle valve job
Rocket spring and titanium retainers
Gsr tranny
Arp rod bolts and head bolts
Any suggestions??
Last edited by sdboosted; 12-10-2014 at 09:36 PM.
#2
Honda-Tech Member
Re: best cams and headers for me??
Use and goals for the car? Budget?
Hands down the Toda rep header will be the best fit for your build for the $$
Tuner 2's, Jun III's, BC 3's are all good fits and easy to make power on
I'll go out on a limb and say pro 2's, but it depends how well the PnP/VJ is if they will be efficient...they may be a bit "big" still.
EDIT: By BC 3's I meant buddy club 3's...not Brian crower
Hands down the Toda rep header will be the best fit for your build for the $$
Tuner 2's, Jun III's, BC 3's are all good fits and easy to make power on
I'll go out on a limb and say pro 2's, but it depends how well the PnP/VJ is if they will be efficient...they may be a bit "big" still.
EDIT: By BC 3's I meant buddy club 3's...not Brian crower
Last edited by 93egSLEEPER; 12-10-2014 at 09:57 PM.
#3
Re: best cams and headers for me??
Use and goals for the car? Budget?
Hands down the Toda rep header will be the best fit for your build for the $$
Tuner 2's, Jun III's, BC 3's are all good fits and easy to make power on
I'll go out on a limb and say pro 2's, but it depends how well the PnP/VJ is if they will be efficient...they may be a bit "big" still.
Hands down the Toda rep header will be the best fit for your build for the $$
Tuner 2's, Jun III's, BC 3's are all good fits and easy to make power on
I'll go out on a limb and say pro 2's, but it depends how well the PnP/VJ is if they will be efficient...they may be a bit "big" still.
Track sometimes daily and goal is 200 hp if possible and for the cams skunk2 is having a sale in Norco ca I might get them if there available also for the headers I was looking at the todas
#4
Honda-Tech Member
Re: best cams and headers for me??
Do some searching on here for header tests. You will get a good feel for what direction to go. Also check out the dyno thread at the top of the forum for ideas of builds
#5
#6
Honda-Tech Member
Join Date: May 2003
Location: r4, mars
Posts: 1,328
Likes: 0
Received 0 Likes
on
0 Posts
Re: best cams and headers for me??
define track.... drag? circuit?
roadrace/circuit il take Pro1 , Buddyclub spec3 for sure...
occasional drag il take the pro2 / m22xx / Jun3 / even the s2s2
if you could get the comp to 11.8-12.3:1 that should be good
assuming the usdm magical typeR is the usdm ITR
roadrace/circuit il take Pro1 , Buddyclub spec3 for sure...
occasional drag il take the pro2 / m22xx / Jun3 / even the s2s2
if you could get the comp to 11.8-12.3:1 that should be good
assuming the usdm magical typeR is the usdm ITR
Trending Topics
#9
#10
Re: best cams and headers for me??
Track as in drag sorry and pro 2 might be the one
#12
Honda-Tech Member
Join Date: Dec 2005
Location: in the heat
Posts: 715
Likes: 0
Received 0 Likes
on
0 Posts
#17
Honda-Tech Member
Join Date: May 2003
Location: r4, mars
Posts: 1,328
Likes: 0
Received 0 Likes
on
0 Posts
Re: best cams and headers for me??
if skunk2 is having a sale.. that should help the OP some..
we all could use a bit of $ savings lol so i still hold to my list of cams that would work on his set up
pro2 / m22xx / Jun3 / even the s2s2
its just an 1840cc motor we cant forget.. he doesnt have the closest geared transmission and or high final drive.. so a healthy mid and good top end would be more important... not... all top end and poopy mid LOL
pulling from the other thread of 93egsleeper
the stage 2 from ddtech would also prolly fit well.. based on the numbers provided
so any of the above cams will work....
we all could use a bit of $ savings lol so i still hold to my list of cams that would work on his set up
pro2 / m22xx / Jun3 / even the s2s2
its just an 1840cc motor we cant forget.. he doesnt have the closest geared transmission and or high final drive.. so a healthy mid and good top end would be more important... not... all top end and poopy mid LOL
pulling from the other thread of 93egsleeper
the stage 2 from ddtech would also prolly fit well.. based on the numbers provided
so any of the above cams will work....
#18
Honda-Tech Member
Re: best cams and headers for me??
DDTECH's stage 1 would fit this motor better. Or a stage 1 w/ a "twist"
The 2's are bigger than pro 2's...which are pretty on point on a healthy 2L motor.
The 2's are bigger than pro 2's...which are pretty on point on a healthy 2L motor.
#20
Honda-Tech Member
Re: best cams and headers for me??
LOL not quite. Just stating stage 1's would fit a 1.8 better than a stage 2..... Would you recommend an M24 over and M22 for this build? No. They would not be sized correctly. Stp starting ****, I'm trying to help.
Read my first post. I didn't mention DDTECH or Rocket in it to avoid BS and people like you putting words in my mouth. I don't buy into the drama. I state facts. You make recommendations on this forum all the time about RM cams.... but do I call you a PR machine? Keep my name out of your mouth...
Read my first post. I didn't mention DDTECH or Rocket in it to avoid BS and people like you putting words in my mouth. I don't buy into the drama. I state facts. You make recommendations on this forum all the time about RM cams.... but do I call you a PR machine? Keep my name out of your mouth...
Last edited by 93egSLEEPER; 12-13-2014 at 11:50 PM.
#21
Honda-Tech Member
Join Date: Feb 2003
Location: schooling kids in ny, usa
Posts: 9,813
Likes: 0
Received 9 Likes
on
9 Posts
Re: best cams and headers for me??
international arguements. gotta love the internet. lets not get this locked up gentlement.
i think the bc3+ wouldnt be a bad cam at all on this motor, you dont need 8500 ish + rpm to make your peak power and still have a nice midrange. thats what id say based off of reading other peoples builds over the years
i think the bc3+ wouldnt be a bad cam at all on this motor, you dont need 8500 ish + rpm to make your peak power and still have a nice midrange. thats what id say based off of reading other peoples builds over the years
#22
Honda-Tech Member
Join Date: May 2004
Location: Dunakeszi, Hungary
Posts: 891
Likes: 0
Received 0 Likes
on
0 Posts
#23
Honda-Tech Member
#24
Honda-Tech Member
Re: best cams and headers for me??
international arguements. gotta love the internet. lets not get this locked up gentlement.
i think the bc3+ wouldnt be a bad cam at all on this motor, you dont need 8500 ish + rpm to make your peak power and still have a nice midrange. thats what id say based off of reading other peoples builds over the years
i think the bc3+ wouldnt be a bad cam at all on this motor, you dont need 8500 ish + rpm to make your peak power and still have a nice midrange. thats what id say based off of reading other peoples builds over the years
I don't ever feel like getting in a mindless argument with the robots on here so I try to keep DD and RM out of my posts and let them do their thing on their own. Everyone seems to have a nuse and pitchfork ready at all times
...
Way bigger?
Some guys just like causing problems
#25
Honda-Tech Member
iTrader: (6)
Join Date: Sep 2004
Location: sunrise, FL, USA
Posts: 1,027
Likes: 0
Received 0 Likes
on
0 Posts
Re: best cams and headers for me??
A lot of the cams mentioned are to big on the the exhaust side for this build, which is why DDtech is a better option since they will be customized to his build. If budget is a issue I would go pro2, they work well on mild and big builds.