FabulousSi

Very very very pimp moogen bling.


[Modified by FabulousSi, 9:23 PM 3/25/2003]

BERT-O

[Modified by BERT-O, 5:02 PM 3/25/2003]


[Modified by BERT-O, 5:04 PM 3/25/2003]

STC

Sweet!!!!

and SWEEEEEET carpet. My carpet is as think as yours.!!!

rated_r

looks good

Nimbus

I love my Twinloop on my ITR as well.

mugenracer

I always wondered this also, i have the old skool mugen sport exhaust on my JDM integra Si, and it has a twin internal loop, which i figured would be more restrictive than a straight through exhaust.....but figure that mugen would hardly design an exhaust system that is going to restrict exhaust gasses?????????? Anyone????

Calavera

I thought the twinloops main purpose was to reduce noise??? anyone???

Btw, is mugen twinloop 2.5" or 2.36 or whatever?

EGtoR

Definitely NOT 2.5"

Eric R

Yes, the main purpose of a twinloop exhaust is to reduce noise and still flow in a efficient way.

Mugen twinloop for JDM I believe is 2.5" ID.

sleeprhatch

j00 must be rich to get the whole system y0! I love my twin loop

itr1244

It's on my car now and i love the sound..

i have a question.. what's the diameter for the mugen b-pipe?

is it 2.25?? i think T1R is 2.5..
mugen b pipe is smaller than my T1R b pipe
any thoughts?

thx

CPR

Not to be technical here but the Mugen DOES NOT reduce noise. It's louder than stock, although not by much. When it's first installed, it's so quiet that it doesn't even seem like you installed it. Once it breaks in, it lets out a pretty subdued but menacing growl but mainly only during acceleration. It's noticeably louder than stock though. It's a 60.5mm exhaust which equates to about 2.36". The piping that's located between the cat and resonator is a little smaller than 60.5mm though.

itr1244

I drove around today and i noticed in sound wise it's EXCTLY same as T1R b-pipe and stock axle back. i could guess it but i was right.
hehe but it's LITTLE louder than stock with T1R b-pipe.
is it good idea to cut the rear section flange out of the mugen B-pipe and weld it in to my T1R b-pipe to go with Mugen Twin loop.
i noticed before the reonator Mugen has smaller piping but at the rear section it's larger (probably 2.5)

itr1244

Here are some pics . I just went down stairs to take some quick snaps


where it bolt on to the CAT or my case test pipe





it's little short for my setup... i will modifiy it later.. it still looks good

Can you guys post pics of your Twin loop on your R as well? i wanna see how it sits on yours
thx

Calavera

So it is true that even if you run 2.5" b pipe the mugen muffler would actually be a bottleneck being 2.36", no?

itr1244

If i run 2.5 " b pipe i dont think there's any bottle neck cuz i think mugen axle back has big diameter with no bottle neck. i am thinking the pipe on axle back is close to 2.5

itr1244

come on.. some one with twinloop post pics plz~

Bob#455

Okay, here you go...

itr1244

damn u.. all i see is your middle finger. haha
didnt help at all.. do u have it in different angle???

purplehazek4

damn i really need to get one of those.
looks good

itr1244

at this point i cant make any reviews yet.
after few days when i can notice the power differeance i will post up
T1R B-PIPE + SPOON n1 VS Mugen Twin loop

JUNDC2

sweet, how much u pay for it.

itr1244

arms and legs

jetydosa

Check out *my* M00gen fizzle!

itr1244

HaHa.. nice photoshop