S1NFUL RL1 619

my son just dropped my keys in a bucket of water about an hour ago. i set it under a light so it could dry up. the remote still turns on just fine with a little bit of water spots in the screen. however, the remote says that the alarm is disarmed (showing the lock as "unlocked")
now i just need to know how do i reprogram the remote without messing with the alarm on the car at all if there is a possible way. what sucks is that i don't have the manual but i do remember reading that if the remote and alarm are not on the same rolling code, then to keep pressing the arm button on the alarm pad until the remote is transmitting to the alarm on the same code, but so far that's not working and it's chirping in sequence each time i press the arm button any single time. it chirps in this sequence, but i don't know if it's significant to anything. *beep beep*beep beep*beep beep*. can anybody help? i need to drive back home tonight, but i don't want to set off the alarm and start ripping through the hood and dash to bypass the alarm. anybody got any suggestions?? p

trick_db

it happen to me once, you might get lucky to get it fix, if not you have to bring to the shop, they will do it for you. the shop charge me 75 bucks with new remote.

S1NFUL RL1 619

i think i'm screwed for fixing it tonight cuz i just pulled up the manual online. and that bs about resetting the rolling codes isn't working. my program button is screwed to or some shiet. i think i gotta look like a car theive for tonight and start pulling out the wiring in a few minutes.

jdm_bones

iTrader: (5)

This happened to me too, take out the battery off the remote...Then dry it out really well, use a blow dryer...then disconect your car battery so that it resets, and then put the battery back it to your remote...Worked for me!

S1NFUL RL1 619

alright, i'm gonna try that right now. i gotta find tools. sucks cuz i'm at a relatives pad in temecula. and i needed to drive back down. i don't even know if they have tools here. thanks for the info.

trick_db

best way, bring to alarm shop, they will fit it for you and give you a new remotoe for 75 bucks. dont take out the brain, cause you might expletive it more up.

S1NFUL RL1 619

well, i just took out the fuse on the brain. so now no alarm as of the time being. but i'm going to have my friend who installed in reprogram the remote for me. and if that doesn't work, i'll just take it into the shop to get a new (2nd) remote. i think i should've bought a back up remote just at the fact having kids. i didn't even know my son nabbed the keys off the dinner table. that little crook! haha

Tizight

My alarm locks and everything but it still says it is unlocked even thought it is armed I just got used to it. My battery Always falls out of the compartment also.

S1NFUL RL1 619

well, in my case, it wasn't even transmitting to the brain. so the algorythm codes weren't matching up. so yeah, it's cool for now i guess, i'm just gonna have the whole system reset and reprogrammed.


Modified by S1NFUL RL1 DB7 at 9:50 AM 9/11/2006

iH8RICERZ

iTrader: (1)

I had my friends that worked and best buy and circuit city help me out since I had no clue how to reprogram my 791vx pager remote. They did it in 45 seconds.... and it costed me $60 for an extra paging remote!

S1NFUL RL1 619

that $#!+ sucks. but my homie that installed the alarm knows some other ways to reprogram other than what's shown in the manual. so i'm gonna go with that and see what happens.

oh, and for the record, disconnecting the battery and reconnecting it again doesn't work.

bigslimdog

I had to reprogram the remote once. Give me your email and I will send you a PDF manual that I found somewhere online like a year ago with instructions on how to reprogram the remote. Hopefully it will help you.

EDIT: oh and if you find out you need a new remote, buy it on ebay for a lot cheaper and then use the instructions i will send you to program the remote

S1NFUL RL1 619

pm sent good lookin out

94b16teg

Open the door (make sure door trigger is hooked up Green or Purple on the main harness)
Turn the ignition to ON and leave it
Within 10seconds do the following
Press the programming button once and then again and hold.(hold on the second press)
Press any button on the transmitter
The siren will chirp or LED will flash
Turn off key before letting go of the button

I am a viper dealer. try this a couple times its kinda hard to get used to the way they program. If it still doesnt work you will need a new remote, try taking it apart and cleaning everything really good and maybe the dealer you got it from can get it warrantied. It should have a life time warranty.

RHDintegXsi

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by 94b16teg &raquo;</TD></TR><TR><TD CLASS="quote">Open the door (make sure door trigger is hooked up Green or Purple on the main harness)
Turn the ignition to ON and leave it
Within 10seconds do the following
Press the programming button once and then again and hold.(hold on the second press)
Press any button on the transmitter
The siren will chirp or LED will flash
Turn off key before letting go of the button

I am a viper dealer. try this a couple times its kinda hard to get used to the way they program. If it still doesnt work you will need a new remote, try taking it apart and cleaning everything really good and maybe the dealer you got it from can get it warrantied. It should have a life time warranty.</TD></TR></TABLE>

finally some legit advice

thanks

we tried reprograming the remot but no luck..tried again with MY remote and it programs fine..remote crapped out

time for a new remote

S1NFUL RL1 619

yeah.. so who's got the hook up on LCD remotes for cheap?

94b16teg

I got one for $70 plus shipping tell me if you want it. thanks justin (remote # 479v)

S1NFUL RL1 619

pm sent