Spoon prepped Type R Motor. B18C. Complete. Socal.
Thread Starter
New User
Joined: Aug 2001
Posts: 1,452
Likes: 0
From: Cypress, CA, USA
Spoon prepped Type R Motor. B18C. Complete. Socal.
ADDED: Dyno Sheet.
Motor dynoed with Spoon ECU. With a programable engine management system there is more HP to be found
ASKING $5500 PICKED UP
http://www.we-todd-did-racing....D.jpg
Block Stamp.
http://www.we-todd-did-racing....D.jpg
Side shot of the motor and water neck w/ engine harness.
http://www.we-todd-did-racing....D.jpg
Block Stamp, made by Honda Motors in Japan
http://www.we-todd-did-racing....D.jpg
IM Shot w/ Spoon Throttle Body
http://www.we-todd-did-racing....D.jpg
LSD Stamp on the Tranny
http://www.we-todd-did-racing....D.jpg
N1 Crank Pulley.
http://www.we-todd-did-racing....D.jpg
Side shot of the motor
http://www.we-todd-did-racing....D.jpg
Spoon TB
Top shot of the whole motor.
http://www.we-todd-did-racing....D.jpg
Another shot of the top of the motor
This motor came running from a Lotus Elise prepared by Prototype Racing. If you were at the Eibach meet it found its home in the green Lotus that now has a K20 w/ a JRSC.
This is a real Spoon Crate motor special ordered from Japan.
This motor is basically a hand built motor with stricter tolerances than a motor from the factory.
Pistons, rods, and valvetrain are carefully selected by weight then matched to the motor.
Spoon crate motors only include the short block. (no distributor, IM, header, engine harness, or tranny). The 98 spec itr tranny was added separately, JDM ITR intake manifold, N1 crank pulley, JDM ITR 4-1 header (ceramic coated) w/ heatshield.
Dynoed at Church Automotive Testing at 192hp to the hubs. Motor comes with dyno sheet.
B18C JDM ITR Motor
Stock Bore with ITR Pistons (1.8L)
ITR Cams
Balanced and Blueprinted Bottom End
JDM ITR 4-1 header (ceramic coated)
Spoon Clutch
ITR Tranny w/ LSD (98 Spec)
N1 Crank Pulley
Spoon Thinner than stock Headgasket (11.3:1 Compression)
Spoon TB 70mm
Spoon ECU
If i missed anything ill be sure to include it.
Call me at the shop or PM me with any questions
Epic Motoring
310 787 1562
Allen
Anyone is welcome to stop by and check out the motor in person.
Modified by psileepR at 11:47 AM 12/1/2004
Motor dynoed with Spoon ECU. With a programable engine management system there is more HP to be found
ASKING $5500 PICKED UP
http://www.we-todd-did-racing....D.jpg
Block Stamp.
http://www.we-todd-did-racing....D.jpg
Side shot of the motor and water neck w/ engine harness.
http://www.we-todd-did-racing....D.jpg
Block Stamp, made by Honda Motors in Japan
http://www.we-todd-did-racing....D.jpg
IM Shot w/ Spoon Throttle Body
http://www.we-todd-did-racing....D.jpg
LSD Stamp on the Tranny
http://www.we-todd-did-racing....D.jpg
N1 Crank Pulley.
http://www.we-todd-did-racing....D.jpg
Side shot of the motor
http://www.we-todd-did-racing....D.jpg
Spoon TB
Top shot of the whole motor.
http://www.we-todd-did-racing....D.jpg
Another shot of the top of the motor
This motor came running from a Lotus Elise prepared by Prototype Racing. If you were at the Eibach meet it found its home in the green Lotus that now has a K20 w/ a JRSC.
This is a real Spoon Crate motor special ordered from Japan.
This motor is basically a hand built motor with stricter tolerances than a motor from the factory.
Pistons, rods, and valvetrain are carefully selected by weight then matched to the motor.
Spoon crate motors only include the short block. (no distributor, IM, header, engine harness, or tranny). The 98 spec itr tranny was added separately, JDM ITR intake manifold, N1 crank pulley, JDM ITR 4-1 header (ceramic coated) w/ heatshield.
Dynoed at Church Automotive Testing at 192hp to the hubs. Motor comes with dyno sheet.
B18C JDM ITR Motor
Stock Bore with ITR Pistons (1.8L)
ITR Cams
Balanced and Blueprinted Bottom End
JDM ITR 4-1 header (ceramic coated)
Spoon Clutch
ITR Tranny w/ LSD (98 Spec)
N1 Crank Pulley
Spoon Thinner than stock Headgasket (11.3:1 Compression)
Spoon TB 70mm
Spoon ECU
If i missed anything ill be sure to include it.
Call me at the shop or PM me with any questions
Epic Motoring
310 787 1562
Allen
Anyone is welcome to stop by and check out the motor in person.
Modified by psileepR at 11:47 AM 12/1/2004
Thread Starter
New User
Joined: Aug 2001
Posts: 1,452
Likes: 0
From: Cypress, CA, USA
Re: Spoon prepped Type R Motor. B18C. Complete. Socal. (Kicker773)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Kicker773 »</TD></TR><TR><TD CLASS="quote">nice but how much would shipping be to 60625</TD></TR></TABLE>
shipping can be done but id rather hold off to a local buyer. id rather have the buyer see this thing in person so we can do a leakdown and compression check in front of them so they know what they are buying.
if it comes to it we may have to ship it out.
bump for more local ppl
shipping can be done but id rather hold off to a local buyer. id rather have the buyer see this thing in person so we can do a leakdown and compression check in front of them so they know what they are buying.
if it comes to it we may have to ship it out.
bump for more local ppl
Trending Topics
Thread Starter
New User
Joined: Aug 2001
Posts: 1,452
Likes: 0
From: Cypress, CA, USA
Re: (lsVtec...)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by lsVtec... »</TD></TR><TR><TD CLASS="quote">how much installed into a dc4?</TD></TR></TABLE>
call me at the shop. 310 787 1562. ask for Allen or Kevin.
call me at the shop. 310 787 1562. ask for Allen or Kevin.
