Autopilot EF9 update
#1
Thread Starter
Join Date: Mar 2004
Location: ARE YOU EXPERIENCED, PURPLE HAZE, STONE FREE
Posts: 1,647
Likes: 0
Received 0 Likes
on
0 Posts
Autopilot EF9 update
ANOTHER SET OF NEW PIXX 1ST PAGE SCROLL DOWN!! THANK YOU
Whats up all you EF heads i was able to take some more photos for you all to check out. Along with the existing photos i added just a few more. Here are some photos of some O.E.M HONDA parts that powder coated, who says i cant restore my HONDA just like a 66 Volkwagen Bus, one day these lil HONDA's will be at a different level than just paint jobs aftermarket parts and engine building. One day attention to detail will be the key!! Enjoy
This is when i first got the EF
Then i started to cut it all up remove all the junk and shave the entire floor pan( end result no holes what so ever " ALL WELDS HERE BONDO "
Replacing all oem hardlines and converting to Army Navy set up.
Hydro clutch assembly fabricated onto the EF no cable type here.
Rear section will also be shaved no lines no wires, just all metal and paint .
engine bay will also be shaved
Fabricating tranny bracket to allow the ITR motor to sit snug. ( donor motor from the old XSi)
Oem usdm bracket seems flimsy this part is still undergoing research.
back view of the ITR motor
looks a little crooooked!
Restored OEM foglight bezel and brackets, powder coated glossy black
restored OEM round type foglights outer casing, brackets all internal components were also powder coated and re dipped in chrome.
front bumper support powder coated, replaced oem hardware with new stainless steel arp studs and green anodized beauty washers.
rear bumper holder powder caoted
Just a few parts that were powder coated( over 300 O.E.M parts will be powder coated and restored and will look 100 times better than when it came out the factory! " Attention 2 Detail"
GOT STAINLESS ?
Here it is fellas and gals i was able to hook up the brake set up. I decided to go with stainless steel hard-line, give it that Hot -Rod style. Briaded lines can be sponge and may cause you to have a decrease in stoppping power. This set up that i was able to complete was for the clutch-line and front brakes to the master cylinder and going to the prop-valve and bulkheads going to the rear. Hope you enjoy the snaps.
[IMGhttp://www.we-todd-did-racing.com/wetoddimage.wtdr/wMTI0MTAwNjZzNDEzZGZkMzF5NTQx.jpg][/IMG]
here it is i was able to finish powder coating all the seat frames for the SiR. The gas tank was restored as well. also many misc parts that were rusted out were sandblasted and chromed, most of these parts wion't even bee seen to the naked eye but this EF is getting the restoration it deserves. thank you for looking.
here are some shots of the oem brake calipers that were restored and powder coated. Converted to Army navy setup.
Thank you for looking and i hope you enjoyed the photo's . Stay tuned for the next update.
Modified by QUESTOYZ by RHanDy at 9:11 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:11 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:12 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:14 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:16 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 7:14 PM 5/12/2006
Modified by QUESTOYZ by RHanDy at 4:34 PM 6/5/2006
Modified by QUESTOYZ by RHanDy at 2:53 PM 6/9/2006
Whats up all you EF heads i was able to take some more photos for you all to check out. Along with the existing photos i added just a few more. Here are some photos of some O.E.M HONDA parts that powder coated, who says i cant restore my HONDA just like a 66 Volkwagen Bus, one day these lil HONDA's will be at a different level than just paint jobs aftermarket parts and engine building. One day attention to detail will be the key!! Enjoy
This is when i first got the EF
Then i started to cut it all up remove all the junk and shave the entire floor pan( end result no holes what so ever " ALL WELDS HERE BONDO "
Replacing all oem hardlines and converting to Army Navy set up.
Hydro clutch assembly fabricated onto the EF no cable type here.
Rear section will also be shaved no lines no wires, just all metal and paint .
engine bay will also be shaved
Fabricating tranny bracket to allow the ITR motor to sit snug. ( donor motor from the old XSi)
Oem usdm bracket seems flimsy this part is still undergoing research.
back view of the ITR motor
looks a little crooooked!
Restored OEM foglight bezel and brackets, powder coated glossy black
restored OEM round type foglights outer casing, brackets all internal components were also powder coated and re dipped in chrome.
front bumper support powder coated, replaced oem hardware with new stainless steel arp studs and green anodized beauty washers.
rear bumper holder powder caoted
Just a few parts that were powder coated( over 300 O.E.M parts will be powder coated and restored and will look 100 times better than when it came out the factory! " Attention 2 Detail"
GOT STAINLESS ?
Here it is fellas and gals i was able to hook up the brake set up. I decided to go with stainless steel hard-line, give it that Hot -Rod style. Briaded lines can be sponge and may cause you to have a decrease in stoppping power. This set up that i was able to complete was for the clutch-line and front brakes to the master cylinder and going to the prop-valve and bulkheads going to the rear. Hope you enjoy the snaps.
[IMGhttp://www.we-todd-did-racing.com/wetoddimage.wtdr/wMTI0MTAwNjZzNDEzZGZkMzF5NTQx.jpg][/IMG]
here it is i was able to finish powder coating all the seat frames for the SiR. The gas tank was restored as well. also many misc parts that were rusted out were sandblasted and chromed, most of these parts wion't even bee seen to the naked eye but this EF is getting the restoration it deserves. thank you for looking.
here are some shots of the oem brake calipers that were restored and powder coated. Converted to Army navy setup.
Thank you for looking and i hope you enjoyed the photo's . Stay tuned for the next update.
Modified by QUESTOYZ by RHanDy at 9:11 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:11 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:12 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:14 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 9:16 PM 4/16/2006
Modified by QUESTOYZ by RHanDy at 7:14 PM 5/12/2006
Modified by QUESTOYZ by RHanDy at 4:34 PM 6/5/2006
Modified by QUESTOYZ by RHanDy at 2:53 PM 6/9/2006
#2
Honda-Tech Member
Join Date: Apr 2005
Location: Los Angeles
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Re: Autopilot EF9 update (QUESTOYZ by RHanDy)
rest in peace brother. i miss you all the time. you did awesome work and i want to thank you over and over again for our friendship and your inspiration. i love you man
Modified by donut. at 1:08 PM 10/17/2006
Modified by donut. at 1:08 PM 10/17/2006
#7
Re: Autopilot EF9 update (CRXone)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by CRXone »</TD></TR><TR><TD CLASS="quote">Questoyz cars </TD></TR></TABLE>
Trending Topics
#15
OG triple OG
Re: Autopilot EF9 update (donut.)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by donut. »</TD></TR><TR><TD CLASS="quote"> </TD></TR></TABLE>
randy you are a ******* butt pirate.
randy you are a ******* butt pirate.
#19
B*a*n*n*e*d
Join Date: Sep 2000
Location: Farmington and La Jolla, MI/CA, USA
Posts: 207
Likes: 0
Received 0 Likes
on
0 Posts
Re: Autopilot EF9 update (DC4me)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Hella_JDM »</TD></TR><TR><TD CLASS="quote">thats da real sheit too , hella japan stylie.</TD></TR></TABLE>
learn to talk like a normal person.
learn to talk like a normal person.
#21
OG triple OG
Re: Autopilot EF9 update (Modest Mouse)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Modest Mouse »</TD></TR><TR><TD CLASS="quote">learn to talk like a normal person.</TD></TR></TABLE>
damn i wish i was from farmington.
damn i wish i was from farmington.
#23
Trial User
Join Date: Apr 2005
Location: Nor Cal, CA, USA
Posts: 1,821
Likes: 0
Received 0 Likes
on
0 Posts
Re: Autopilot EF9 update (Dspec)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Dspec »</TD></TR><TR><TD CLASS="quote">RHD </TD></TR></TABLE> MMmmM HhHhmmmm