Lots O parts d series and b series parts 56K NO WAY
Thread Starter
Joined: Sep 2002
Posts: 998
Likes: 0
From: Port St. Lucie, Florida, USA
Lots O parts d series and b series parts 56K NO WAY
Here are some parts that i have to clean out of my garage, everything is in good working order pm me with any questions
<U>ALL PARTS ARE OBO NEED TO SELL</U>
<U>VX Engine Harness Uncut $75</U>
<U>OBD 1 Po7 VX ECU $30 NOW $30 SHIPPED</U>
<U>VX Exhaust Manifold Belive Same As Hf for Homemade Turbo Kits $45 Now $35</U>
<U>OBD 1 D Series Alternator $45 NOW $45 shipped</U>
<U>GSR Intermidiate Shaft $75</U>
<U>JDM ITR Axles 36mm Axles needed for use with JDM 5 LUG $120 SOLD</U>
<U>B Series Motor Mounts Missing Rear Ruber mount $80</U>
<U>Integra Lower Tie bar will fit EG $30 NOW $20</U>
<U>EG Stock Air Box $ 10</U>
<U>OBD 1 VX 5 WIRE O2 sensor $10</U>
Modified by mxpx035 at 1:45 PM 1/22/2006
Modified by mxpx035 at 9:38 PM 1/23/2006
Modified by mxpx035 at 8:55 PM 1/27/2006
Modified by mxpx035 at 9:17 PM 1/30/2006
<U>ALL PARTS ARE OBO NEED TO SELL</U>
<U>VX Engine Harness Uncut $75</U>
<U>OBD 1 Po7 VX ECU $30 NOW $30 SHIPPED</U>
<U>VX Exhaust Manifold Belive Same As Hf for Homemade Turbo Kits $45 Now $35</U>
<U>OBD 1 D Series Alternator $45 NOW $45 shipped</U>
<U>GSR Intermidiate Shaft $75</U>
<U>JDM ITR Axles 36mm Axles needed for use with JDM 5 LUG $120 SOLD</U>
<U>B Series Motor Mounts Missing Rear Ruber mount $80</U>
<U>Integra Lower Tie bar will fit EG $30 NOW $20</U>
<U>EG Stock Air Box $ 10</U>
<U>OBD 1 VX 5 WIRE O2 sensor $10</U>
Modified by mxpx035 at 1:45 PM 1/22/2006
Modified by mxpx035 at 9:38 PM 1/23/2006
Modified by mxpx035 at 8:55 PM 1/27/2006
Modified by mxpx035 at 9:17 PM 1/30/2006
Re: Lots O parts d series and b series parts 56K NO WAY (mxpx035)
IM you.
looking for vx/cx throttle stay bracket on the intake manifold.
vx tiny *** intake piping ARM
eg radiator...BUT only need the rubber bushings on the bottom of rad that sits on the cross member
looking for vx/cx throttle stay bracket on the intake manifold.
vx tiny *** intake piping ARM
eg radiator...BUT only need the rubber bushings on the bottom of rad that sits on the cross member
Trending Topics
Thread Starter
Joined: Sep 2002
Posts: 998
Likes: 0
From: Port St. Lucie, Florida, USA
Re: (Dr. D-Series)
shipped and cheap don't go together a motor is heavy i can take off the head but i am not strippin the internals i only want like 20 for the motor but good luck on cheap shipping
Thread
Thread Starter
Forum
Replies
Last Post
